B
Hot Keys:
CHARGER
The
GEN
(erator) hot
key (
A
) brings up
Generator Status
,
with readings and
start/stop commands
for the Advanced
Generator Start
(AGS) mode.
GEN
EVENTS
BATTERY STATUS
INVERTER
GEN
CHARGER
EVENTS
FAVORITE
AC INPUT
OutBack Power
1.5 kW
0.1 kW
115 V
1.5 kW
85%
28.5 V
System
OK
0.00 kW
0.0 kW
G
G
OutBack Power
1.5 kW
1.5 kW
115 V
1.5 kW
85%
28.5 V
System
OK
0.00 kW
0.0 kW
G
G
A
A1
is the screen as it appears
with no generator activity.
E
F
D
G
M2
is the screen as it appears
with generator activity.
H
I
J
C
B
Basic Navigation
Soft Keys
Four “soft” keys are located directly below the display. Soft key functions will vary depending on the location. These
functions are identified by icons or text directly above the key. Occasionally not all four soft keys are used.
o
In all cases where displayed, the
<
Back
>
soft key returns to the previous screen. The
<
Port
>
soft key cycles through each device
connected to the network. When a specific port is selected, the device on that port can be individually programmed with whatever
options are available. (Programming is often global unless assigned to a particular port.) Other soft keys are described as appropriate.
Home Screen Soft Keys
See the following pages for displays and descriptions.
The
<
Charge Controller
>
soft key (
O
) displays information on all FLEXmax charge
controllers. If no controllers are detected by the HUB Communications Manager,
O
is
inoperative. (The symbol and meter bar are not present.) See page 14.
The
<
Battery
>
soft key (
P
) displays information on the battery bank. The information
available depends on whether the FLEXnet DC battery monitor is installed. See page 12.
The
<
Inverter
>
soft key (
Q
) displays information on any inverters present on the HUB.
If no inverters are present,
Q
is inoperative. (The symbol is not present.) See page 8.
For FX-class inverters: In the
Off Grid
system type,
R
is
<
Input Select
>
. It may not have
a symbol. The symbol only appears if a generator is running. (See
J
.) In
Grid Tied
,
R
is
<
Grid Status
>
. will appear. In
Backup
,
R
is inoperative. See page 8.
In the
Off Grid
system type: For FXR-class inverters,
S
is the
<
Input Select
>
soft key. For Radian-class inverters,
S
is the
<
Input Priority
>
soft key. It may not have a symbol. The symbol only appears if a generator is running. (See
J
.)
For both FXR- and Radian-class: In
Grid Tied
or
Off Grid
,
S
is the
<
Grid Status
>
soft key.
will appear. See page 8.
Meter Bar or Metering Notes
In the
Off Grid
or
Backup
system types:
“OK” is replaced with
!
(with an event
message) during a generator fault.
In the
Grid Tied
system type: “OK” is
replaced with
!
(with an event message)
during a grid fault.
In any system type:
“OK” is replaced with
!
or
X
(with an event message) if the FN-DC is
present and registers a battery problem.
“OK” is replaced with
!
(with an
event message) during an inverter fault.
In the FM100-AFCI, if an AFCI, GFDI, rapid
shutdown, or input fault occurs, the meter bar
also displays
!
.
In the
Backup
system type, the
System
Information
menu must have an AC generator
selected. Otherwise this field is blank. (See the
MATE3s Programming Guide
.)
If
Gen Type
is set to DC, then the left meter bar is
scaled according to the
Max Inverter kW
setting.
A
J
L
O
P
Q
R
S
O
P
Q
G
G
Page 18
900-0124-01-02 Rev B
©2017 OutBack Power. All Rights Reserved.
Page 7
Soft Keys
D
J
K
L
11/13/15
Hot Keys:
GEN & EVENTS
