background image

F D C 3 3 0 2   U s e r   M a n u a l

28

A P P E N D I X   D

29

F D C 3 3 0 2   U s e r   M a n u a l

S P E C I F I C A T I O N S

SSB Phase Noise @ 10 MHz and +13 dBm output level*:

   

At 1 Hz   

< -135 dBc/Hz

   

At 10 Hz 

< -145 dBc/Hz

   

At 100 Hz 

< -153 dBc/Hz

   

At 1 kHz 

< -160 dBc/Hz

   

At 10 kHz 

< -163 dBc/Hz

   

* See chart below for typical additive phase noise performance.

External Alarm Input/Disable Inputs (A or B):

Normal State:  TTL low.  

Alarm State:  TTL high or high Z (internal 10kΩ pull-up).

Connectors:  Rear-panel female BNCs labeled “Disable In”.

Alarm Output: 

Open-collector, 40 VDC Max, 100 mA Max Saturation Current.

High Impedance when any fault condition exists.

Connector:  Rear-panel female BNC labeled “Alarm Out”.

Front-Panel System Status Indicators:

Signal Input LEDs:  Red/Green/Yellow LEDs indicate signal presence, selection status of each Signal 

Input and, if configured, Disable Input (external alarm input) status.

Signal Output LEDs:  Red/Green/Yellow LEDs indicate signal presence status on each output.

Power LEDs:  Red/Green LEDs indicate power supply status of each power input.

Alarm LED:  Red/Green/Yellow LED indicates a serious fault condition.

Maintenance Port:

See 

RS-232 Serial I/O Port Signal Definitions

 in 

Chapter 3

 for more information.

RS-232 serial I/O on rear panel DB9M jack for secure, local terminal access.

User-Selectable Parameters:  9600 to 57600 baud, 

   

 

 

7 or 8 data bits, 

   

 

 

odd, even or no parity, 

   

 

 

1 or 2 stop bits

-180

-170

-160

-150

-140

-130

-120

-110

-100

1

10

100

1000

10000

10

5

EndRun Technologies FDC3302 Distribution Chassis

Typical Phase Noise -- 10 MHz @ +13 dBm

Measured

Curve Fit

Specification

Ph

as

e

N

oi

se

L(

f),

dB

c/

H

z

Fourier Frequency, Hz

Curve Fit Results

White PM

(rad^2): -165.37 dBc/Hz

Flicker PM

(rad^2/Hz): -144.43 dBc/Hz @ 1Hz

Summary of Contents for FDC3302















































Reviews: