background image

F D C 3 3 0 2   U s e r   M a n u a l

27

"Smarter Timing Solutions"

Appendix

D

Specifications

 

Reference Inputs (A or B):

Frequency Range:  100 kHz to 30 MHz.

Impedance:  50Ω, SWR < 1.1.

Amplitude:  +13 dBm Full Performance, +2 dBm minimum, +15 dBm maximum.

A Input to B Input Isolation:  < -105 dB, full frequency range.

Output to Input (Reverse) Isolation:  < -110 dB, full frequency range.

Protection:  Protected to 24V peak-to-peak.

Connectors:  Rear-panel female BNCs labeled “Signal In”.

Distribution Outputs (1 through 10):

Impedance:  50Ω, SWR: < 1.8 @ 100 kHz, <1.2 @ 1 MHz, < 1.3 @ 10 MHz, < 1.8 @ 30 MHz.

Unity Gain:  0 dB, +/-2 dB.

Harmonics:  < -40 dBc @ 13 dBm and 100 kHz <= F <= 20 MHz, 

   

 < -35 dBc @ 13 dBm and F > 20 MHz, 

   

 < - 30 dBc @ 15 dBm.

Spurious:  < -110 dBc.

Protection:  Outputs may be shorted to ground with no damage.  

Connectors:  Rear-panel female BNCs numbered 1 through 10.

Adjacent Output to Output Isolation:

-160

-150

-140

-130

-120

-110

-100

-90

-80

10

5

10

6

10

7

EndRun Technologies FDC3302 Distribution Chassis

Typical Adjacent Channel Isolation

Measured

Specification

HP 3577A Floor

Is

ol

at

io

n,

dB

Frequency, Hz

Summary of Contents for FDC3302















































Reviews: