Endress+Hauser PROMAG 33, Operating Manual

Page: 118 / 126

PULSE / FREQ. OUTPUT (continued)
OUTPUT SIGNAL
(p. 56) PASSIVE / POSITIVE
(open collector / active-high)
PASSIVE / NEGATIVE
(open collector / active-low)
AKTIVE / POSITIVE
(push-pull / active-high)
AKTIVE / NEGATIVE
(push-pull / active-low)
Your setting: ............................................
FAILSAFE MODE
(p. 57)
FALLBACK VALUE
(corresponding to zero flow)
LAST VALUE
(last valid measured value is held)
ACTUAL VALUE
(normal measured output despite fault)
Your setting: ............................................
SIMULATION
FREQ.
(p. 57)
OFF
– 0 Hz (fallback value) – 2 Hz –
10 Hz – 1 kHz – 10 kHz
Your setting: ............................................
NOMINAL FREQ.
(p. 57) Displayed value: 0.00...16383 Hz
RELAYS
RELAY 1
FUNCTION
(p. 58) FAILURE
EPD
ERROR + EPD
DUAL RANGE MODE
BATCH PRECONTACT
FLOW DIRECTION
LIMIT FLOWRATE 1
Your setting: ............................................
RELAY 1
ON-VALUE
(p. 59) 5-digit floating point:
e.g. 1.0000 dm
3
/min
Your setting: ............................................
RELAY 1
OFF-VALUE
(p. 59) 5-digit floating point:
e.g. 10.000 dm
3
/min
Your setting: ............................................
RELAY 2
FUNCTION
(p. 62) EPD
DUAL RANGE MODE
BATCH CONTACT
FLOW DIRECTION
LIMIT FLOWRATE 2
Your setting: ............................................
RELAYS (continued)
RELAY 2
ON-VALUE
(p. 62) 5-digit floating point: e.g. 1.000 dm
3
/min
Your setting: ............................................
RELAY 2
OFF-VALUE
(p. 62) 5-digit floating point: e.g. 10.000 dm
3
/min
Your setting: ............................................
BATCHING
BATCH VARIABLE
(p. 64) OFF – VOLUME
Your setting: ............................................
BATCH QUANTITY
(p. 64) 5-digit floating point: e.g. 240.00 l
Factory setting:
0.0000
[unit]
Your setting: ............................................
BATCH PREWARN
(p. 64) 5-digit floating point: e.g. 200.00 l
Factory setting:
0.0000 [unit]
Your setting: ............................................
COMPENS.
QUANTITY
(p. 65) 5-digit floating point: e.g. –10.00 l
Factory setting:
0.0000 [unit]
Your setting: ............................................
BATCHING
(p. 65) START – STOP – CANCEL
(
1
activates START or STOP)
MAX. BATCH TIME
(p. 65) max. 5-digit number: 0...30000 s
Factory setting:
0 s
Your setting: ............................................
BATCH CYCLE
(p. 65) Display:
max. 7-digit number (0...9999999)
Factory setting: 0
RESET
BATCH CYCLE
(p. 65) NO – YES
DISPLAY
TOTAL VOLUME
(p. 66) Display: max. 7-digit floating point
0,0000...9999999 [unit]
Factory setting: 0.0000 [unit]
TOTAL
OVERFLOW
(p. 66) Display:
e.g. 74 e7 dm
3
= 74,000,000 dm
3
Factory setting: 0
RESET
TOTALIZER
(p. 67) NO – YES
FLOW RATE
(p. 67) Display: max. 5-digit number
–99999...+99999 [unit]
10 Functions at a Glance Promag 33
118 Hauser