Endress+Hauser magphant Operating Instructions Manual Download Page 39

Page: 39 / 44

Magphant

Technical data

Hauser

Pipe nominal diameter

mm (in)

H for installation in steel pipes

mm (in)

H for installation in plastic pipes

250 (9.84)

207.5 (8.169)

≥300 (11.81)

201.5 (7.933)

Dimensions of welding sockets →  15

Weight

1.2 kg (2.6 lb)

Materials

Sensor

• Sensor tip:

• PVDF

• Viton O-ring

• Electrodes:

Stainless steel, 1.4435 (316L)

• Sensor sleeve:

• Stainless steel, 1.4435 (316L) with clamping ring 1.4571 (316Ti) for welding socket

1.4435 (316L)

• Stainless steel, 1.4435 (316L) with clamping ring and NBR seal for welding socket ST.

37/A570

Welding socket (for steel pipes)

• Stainless steel, 1.4435 (316L)

• Steel St.37/A570

Adapter piece (for plastic pipes)

• Stainless steel, 1.4435 (316L)

• Viton O-rings

Plastic union nut (for plastic pipes)

PVC

Transmitter housing

Powder coated die-cast aluminum

15.11 Human interface

Local operation

The device is operated and configured via operating and display elements on the

transmitter →  25.

Communication

The measured values are communicated to a higher-level system via the current output.

15.12 Certificates and approvals

Currently available certificates and approvals can be called up via the product

configurator.

Summary of Contents for magphant













































Search results

Summary of Contents for magphant

Reviews:

Related manuals for magphant

Brands by name

Popular brands

Endress+Hauser magphant, Operating Instructions Manual

Search results

Summary of Contents for magphant

Reviews:

Related manuals for magphant

Brands by name

Popular brands