Endress+Hauser magphant Operating Instructions Manual Download Page 33

Page: 33 / 44

Magphant

Accessories

Hauser

Accessories

Various accessories are available for the device, and can be ordered with the device or at a

later stage from Hauser. An up-to-date overview of accessories is available from

your local Hauser sales organization or on the product page of the Endress

+Hauser website:

www.endress.com

Cover set

Order number

Description

50093653

Cover set, MAGPHANT

Connection set (process)

Order number

Description

50093656

Welding socket set, DN 40 to 2000; 1.4435/316L

50093657

Welding socket set, DN 40 to 2000; St37/A570

50093658

Welding socket set, DN 25; 1.4435/316L

50093659

Welding socket set, DN 25; St37/A570

50093662

Socket set for connection, PVC

Connection set (electrical)

Order number

Description

50093671

Set, 2 extensions PG16 /NPT1/2"

50093672

Set, 2 extensions PG16 /G 1/2"

50093673

Set, 2 extensions PG16 /M20x1.5

Seal set

Order number

Description

50093631

Set, NBR seal, connection St37/A570

Set, electronics

Order number

Description

50093564

Set, electronics module, MAGPHANT

50093522

Set, 10 fuses T 0A16/250

Summary of Contents for magphant













































Search results

Summary of Contents for magphant

Reviews:

Related manuals for magphant

Brands by name

Popular brands

Endress+Hauser magphant, Operating Instructions Manual

Search results

Summary of Contents for magphant

Reviews:

Related manuals for magphant

Brands by name

Popular brands