Endress+Hauser HART Proline Promass 83 Operating Instructions Manual Download Page 131

Page: 131 / 148

Proline Promass 83

Technical data

Hauser

131

10.7

Installation

Installation instructions

→

Inlet and outlet runs

There are no installation requirements regarding inlet and outlet runs.

Length of connecting cable
remote version

max. 20 m (65 ft)

System pressure

→

10.8

Environment

Ambient temperature range

Sensor and transmitter:
• Standard: –20 to +60 °C (-4 to +140°F)
• Optional: –40 to +60 °C (-40 to +140°F)

Note!
• Install the device at a shady location. Avoid direct sunlight, particularly in warm climatic

regions.

• At ambient temperatures below –20 °C (–4 °F) the readability of the display may be

impaired.

Storage temperature

–40 to +80 °C (–40 to +175 °F), pref20 °C (+68 °F)

Degree of protection

Standard: IP 67 (NEMA 4X) for transmitter and sensor

Shock resistance

According to IEC 60068-2-31

Vibration resistance

Acceleration up to 1 g, 10 to 150 Hz, following IEC 60068-2-6

CIP cleaning

Yes

SIP cleaning

Yes

Electromagnetic
compatibility (EMC)

To IEC/EN 61326 and NAMUR Recommendation NE 21

Summary of Contents for HART Proline Promass 83





















































































































































Search results

Summary of Contents for HART Proline Promass 83

Reviews:

Related manuals for HART Proline Promass 83

Brands by name

Popular brands

Endress+Hauser HART Proline Promass 83, Operating Instructions Manual

Search results

Summary of Contents for HART Proline Promass 83

Reviews:

Related manuals for HART Proline Promass 83

Brands by name

Popular brands