background image

Operation

Automatic Boat Drive

18

Figure 7 Quartz boat with the carrier material inserted

NOTICE

Only use a single undamaged piece of quartz fleece as carrier material! When using sev-
eral small or damaged pieces, correct functionality cannot be ensured.

5.3

Manual sampling

Solid sample

Prerequisite: System components have been switched on, the multiWin control and
analysis software is running, an appropriate method has been selected.

}

Fill a quartz boat with carrier material 
(→ "Preparing the quartz boat for the analysis" 

 17).

NOTICE

Temper both components or use tempered components. 
As an exception, AOX and EC/OC measurements do not require carrier material.

}

Weigh the solid sample into a quartz boat.

}

When prompted by the software to do so, use tweezers to insert the quartz boat into
the open sample sluice, making sure that the eye is placed onto the hook.

}

Click on [OK] to confirm that the quartz boat has been inserted.

ü

The sample sluice closes. After a rinsing time has elapsed, which can be config-
ured in a method, the quartz boat is transported into the combustion tube ac-
cording to the parameters specified in the method.

Liquid sample

Prerequisite: System components have been switched on, the multiWin control and
analysis software is running, an appropriate method has been selected.

}

Fill a quartz boat with carrier material 
(→ "Preparing the quartz boat for the analysis" 

 17).

NOTICE

Temper both components or use tempered components.
If no quartz fleece is used, uncontrolled spontaneous evaporation of the complete sam-
ple or splashing of the sample may occur. In the worst case, the system is contaminated!

Summary of Contents for 450-126.416












































Reviews: