background image

26127-5-0111

Page 3

IMPORTANT SAFETY INFORMATION

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

•  Due to high temperatures the appliance should 

be located out of traffic and away from furniture 

and draperies.

•  The  glass  front  or  any  part  removed  for 

servicing the appliance must be replaced prior 

to  operating  the  appliance.  Work  should  be 

done by a qualified service person.

•  Keep burner and control compartment clean. 
•  Vent  cap  is  hot  while  fireplace  is  in 

operation.

• 

Installation  and  repair  should  be  done  by  a 

qUALIFIED SERVICE PERSON. The appliance 

should be inspected before use and at least 

annually by a qualified service person. More 

frequent  cleaning  may  be  required  due 

to  excessive  lint  from  carpeting,  bedding 

materials,  etc.  It  is  imperative  that  control 

compartments,  burners  and  circulating  air 

passageways of the appliance be kept clean.

•  Do noT put anything around the fireplace that 

will obstruct the flow of ventilation air.

•  Clearance in accordance with local installation 

codes  and  the  requirements  of  the  gas 

supplier.

•  Do

  keep  the  appliance  area  clear  and  free 

from combustible material, gasoline and other 

flammable vapors and liquids.

•  Do

 examine venting system periodically and 

replace damaged parts.

•  Do 

make a periodic visual check of pilot and 

burners. Clean and replace damaged parts.

•  CAUTIon:  The  glass  used  in  your  fireplace 

is tempered glass. If the glass is cracked or 

damaged  in  any  way,  it  should  be  replaced 

only  with  a  complete  glass  frame  assembly 

from  Empire.  See  parts  list  on  Page

 

30  for 

ordering.

•  Do noT use this fireplace if any part has been 

under water. Immediately call a qualified service 

technician to inspect the heater and to replace 

any part of the control system and any gas 

control which has been under water.

•  Any  safety  screen  or  guard  removed  for 

servicing an appliance must be replaced prior 

to operating the appliance.

•  This appliance must be installed on a flat, solid, 

continuous surface (e.g. wood, metal, concrete). 

This may be the floor, or it may be raised up on 

a  platform  to  enhance  its  visual  impact.  The 

appliance may be installed on carpeting, tile, 

wood  flooring  or  other  combustible  material 

as the appliance's base extends the width and 

depth of the appliance.

•  Children  and  adults  should  be  alerted  to  the 

hazards of high surface temperatures and should 

stay away to avoid burns or clothing ignition.

•  Young children should be carefully supervised 

when  they  are  in  the  same  room  as  the 

appliance.

•  Clothing or other flammable material should not 

be placed on or near the appliance.

•  Adequate accessibility clearances for servicing 

and proper operation.

•  This appliance must not share or be connected 

to a flue serving a separate solid-fuel burning 

appliance.

•  Keep  the  area  around  your  appliance  clear 

of  combustible  materials,  gasoline  and  other 

flammable vapor and liquids. 

•  Under no circumstances should any solid fuels 

(wood, coal, paper or cardboard etc.) be used 

in this appliance.

•  The flow of combustion and ventilation air must 

not be obstructed in any way.

Summary of Contents for DVP30CA30BN-2









































Reviews: