Emos RAP CT KARGO Bange Operation Manual Download

Page: 7 / 88

Charging instructions

Charging precautions

◆

Please charge with the dedicated charging device provided by RAP
Intelligent Vehicle:

» Do not modify, disassemble or repair the charging device.

Do not use extra wires or adapters to avoid the risk of ﬁre or electric

shock.

» Please stop charging immediately when the charging fails or there is

an abnormality.

» Please do not use the charging device when the protective package is

cracked or any damage is revealed.

» Do not allow minors to touch or use charging devices, and do not let

minors approach during use.

» Please do not pull the cable directly to move the charging device.

When you move it, please handle it gently.

◆

Please choose to charge in a relatively safe environment (such as

avoiding liquids, ﬁre sources, etc.).

◆

The arc may occur during charging. Do not expose to ﬂammable gases

and keep them ventilated to avoid danger.

◆

If the vehicle needs to be parked for a long time without using, please

charge the vehicle ﬁrst.

◆

When charging, please make sure that the charging plug is in good
contact with the charging socket, otherwise it will lead to safety accidents.

◆

Before starting the vehicle, please make sure that the charging device
has been disconnected and the charging port cover has been closed.

◆

If you need to travel on a rainy day while your vehicle is running low and
needs to be charged, we advise you to properly operate according to the
following requirements when using outdoor charging devices:

» Choose a higher location to park and recharge to prevent the battery

from soaking in the water.

Summary of Contents for RAP CT KARGO Bange

























































































Search results

Summary of Contents for RAP CT KARGO Bange

Reviews:

Related manuals for RAP CT KARGO Bange

Brands by name

Popular brands

Emos RAP CT KARGO Bange, Operation Manual

Search results

Summary of Contents for RAP CT KARGO Bange

Reviews:

Related manuals for RAP CT KARGO Bange

Brands by name

Popular brands