Emos RAP CT KARGO Bange Operation Manual Download

Page: 20 / 88

Operation guide

Instrumentation

and sensor, the information of reverse image and sensor will be

displayed by the instrument ﬁrst.

Clock display

◆

It is used to display the current time, the clock can be set in the menu
settings.

Combination meter indicator / warning light

Left/right turn indicator

Position light indicator

High beam indicator

Rear fog light indicator

Low beam indicator

Charging connection
indicator

READY

READY indicator

Motor fault indicator

Low battery indicator

Power limit indicator

Parking brake indicator

Left / right turn indicator

◆

When the turn light is turned on, the turn light and the turning indicator

on the corresponding side ﬂashes at the same time; When the turn light

is turned off, the turn light and the turning indicator on the corresponding

Summary of Contents for RAP CT KARGO Bange

























































































Search results

Summary of Contents for RAP CT KARGO Bange

Reviews:

Related manuals for RAP CT KARGO Bange

Brands by name

Popular brands

Emos RAP CT KARGO Bange, Operation Manual

Search results

Summary of Contents for RAP CT KARGO Bange

Reviews:

Related manuals for RAP CT KARGO Bange

Brands by name

Popular brands