Emerson RXi2-BP Hardware Reference Manual Download Page 28 | Manualshive

Page: 28 / 45

background image

RXi2-BP Hardware Reference Manual

Section 6

GFK-3187B

November 2020

Troubleshooting

23

6.1.4.1

Ethernet Ports LEDs

Same configuration for all Ethernet ports:

Figure 20: Ethernet Ports LEDs

6.1.5

USB2 / USB3.2Gen1

The RXi2-BP provides two USB2 (USB 3 & 4) and two USB3.2 Gen1 (USB 1 & 2) ports. All four are USB
type-A connectors.

Each port (USB2 and USB3.2 Gen1) is protected with an electrical fuse rated up to 1 A.
For normal operation, please do not exceed 900mA for USB3.2 Gen1 and 500mA for USB2.

6.1.5.1

USB2

Figure 21: USB2 Port and Pinout

Signal Name

Pin

VCC (5V_SBY)

1

USB-

2

USB+

3

GND

4

Pin

LED color

LED status indication

12

Green

ACT/LINK
Blink with activity,
Steady on with no activity at 10/100/1000

13/14

Green

Yellow

Off

LINK1000 (steady on)
LINK100 (steady on)
LINK10

«
...
26
27
28
29
30
...
»

Summary of Contents for RXi2-BP














































Reviews:

No comments

Related manuals for RXi2-BP

Brand: Camozzi Pages: 2

Brand: NARGESA Pages: 37

Brand: NARGESA Pages: 6

Brand: Baileigh Industrial Pages: 12

Brand: ABB Pages: 136

Brand: ABB Pages: 108

Brand: Grundfos Pages: 43

Allen-Bradley PowerFlex 755T Flux Vector Tuning

Brand: Rockwell Automation Pages: 116

Brand: OmniCure Pages: 2

Brand: Parker Pages: 40

Brand: Aerovent Pages: 28

GQM2195C2E300JB12 Series

Brand: Murata Pages: 25

Brand: Wachs Pages: 24

Brand: Vestil Pages: 4

Tripod Turnstile

Brand: ZKTeco Pages: 10

Brand: Valmet Pages: 49

Brand: Baileigh Pages: 36

Brand: M&R Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands