Emerson RXi2-BP Hardware Reference Manual Download Page 32 | Manualshive

Page: 32 / 45

background image

RXi2-BP Hardware Reference Manual

Section 6

GFK-3187B

November 2020

Troubleshooting

27

6.3.2

Temperature Sensor

UEFI Firmware sets up two thermal zones on the RXi2-BP carrier board that can be observed with an
EMC2113 device. This device contains internal temperature sensors. Three external temperature
sensors are also connected.
All external sensors are grouped as one thermal group and placed so that the hottest point can be
observed, no matter the mounting style.
The EMC2113 device measures the temperature of several higher-rated devices (GBE; Multi I/O; PCIe
Switch) with the help of a common heatsink.
Please also refer to Section 6.1.2

for additional information.

«
...
30
31
32
33
34
...
»

Summary of Contents for RXi2-BP














































Reviews:

No comments

Related manuals for RXi2-BP

Brand: Xycom Pages: 99

Brand: Wasp Pages: 50

Brand: ALLSPEEDS Pages: 22

Brand: NTN Pages: 19

Brand: Jäger Pages: 40

VQD1000-V Series

Brand: SMC Networks Pages: 5

Brand: Vecow Pages: 139

Brand: vc999 Pages: 96

Brand: Hakko Electronics Pages: 4

BRADEN PD21A Series

Brand: Paccar Winch Pages: 31

Brand: Panblast Pages: 9

Brand: Vantron Pages: 17

Brand: ZIEHL Pages: 30

Brand: hager Pages: 6

Curaflex Nova Uno/M/Z

Brand: DOYMA Pages: 4

Brand: GE Pages: 8

WAVE Cabinet 20

Brand: GE Pages: 24

Brand: Komatsu Utility Pages: 302

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands