manualshive.com logo in svg

Emerson RXi2-BP, Hardware Reference Manual

Share
Download
Emerson RXi2-BP Hardware Reference Manual Download Page 33

RXi2-BP Hardware Reference Manual 

Section 7 

GFK-3187B 

November 2020 

 

Troubleshooting   

28 

Section 7:

 

Hardware and Firmware Programmable 

Devices 

7.1

 

SMBUS Devices 

Device 

Address [7b format] 

Function 

PI6CDBL402B 

6Eh 

Clock Buffer 4x 

TCA9554 

20h 

SMB Port Expander 

EMC2213 

2Eh 

Temperatur Controller 

PI7C9X2G608GP 

68h 

PCIe Switch 

 

7.2

 

I2C Devices 

Device 

Address [7b format] 

Function 

24C64 

57h 

Carrier EEPROM 

TCA9554 

20h 

I2C Port Expander 

 

7.3

 

Ethernet  

The Ethernet controllers provide an iNVM, which contains the MAC address, as well as their 
configuration. This content is not accessible to the user. 

7.4

 

PCIe Switch 

The PCIe switch has a dedicated EEPROM connected for configuration and is not accessible to the user. 

7.5

 

Multi I/O 

The Multi I/O controller (in this system, configured to 2x serial and 1x SPI bridge) has a dedicated 
EEPROM connected for configuration and is not accessible to the user. 

 

 

 

Summary of Contents for RXi2-BP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands