manualshive.com logo in svg

Emerson Rosemount 2051, Reference Manual, Page: 49 / 228

Share
Download
Emerson Rosemount 2051 Reference Manual Download Page 49

39

Reference Manual 

00809-0100-4107, Rev BA

Section 3: Hardware Installation

April 2013

Hardware Installation

Figure 3-6. Flat mounting bracket option codes B3 and BC

A. 1.625 (41)
B. 2.125 (54)
C. 2.81 (71)
D. 8.00 (203)
Note: Dimensions are in inches (millimeters).

1.

Finger-tighten the bolts.

2.

Torque the bolts to the initial torque value using a crossing pattern (see 

Table 3.4.2

 for 

torque values).

3.

Torque the bolts to the final torque value using the same crossing pattern.

Mounting brackets

Rosemount 2051 transmitters may be panel-mounted or pipe-mounted via an optional 
mounting bracket. Refer to 

Table 3-2

 for the complete offering and see 

Figure 3-7

 through 

Figure 3-6

 on pages 

41

 and 

39

 for dimensional and mounting configuration information.

B

C

D

A

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments