manualshive.com logo in svg

Emerson Rosemount 2051, Reference Manual

The Emerson Rosemount 2051 is a powerful and versatile pressure transmitter designed for accurate and reliable measurement. Our Quick Installation Manual provides step-by-step instructions for effortless set up. Download the manual for free at manualshive.com and gain access to all the essential information needed to maximize the performance of this exceptional product.

Share
Download
background image

93

Reference Manual 

00809-0100-4107, Rev BA

Section 7: Safety Instrumented Systems Requirements

April 2013

Safety Instrumented Systems Requirements

Section  7

Safety Instrumented Systems 
Requirements

Safety Instrumented Systems (SIS) Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 93

7.1

Safety Instrumented Systems (SIS) Certification

The safety-critical output of the Rosemount 2051 is provided through a two-wire, 4 - 20 mA 
signal representing pressure. The Rosemount 2051 safety certified pressure transmitter is 
certified to: Low Demand; Type B.   
SIL 2 for random integrity @ HFT=0
SIL 3 for random integrity @ HFT=1
SIL 3 for systematic integrity

7.1.1

Rosemount 2051 safety certified identification

All Rosemount 2051 transmitters must be identified as safety certified before installing into SIS 
systems. 

To identify a safety certified Rosemount 2051C, Rosemount 2051T, Rosemount 2051L:

1.

Check Namur Software Revision located on the metal device tag. "SW _._._".

2.

Transmitter Output Code "A" ( 4-20 mA HART).

7.1.2

Installation in SIS applications

Installations are to be performed by qualified personnel. No special installation is required in 
addition to the standard installation practices outlined in this document. Always ensure a 
proper seal by installing the electronics housing cover(s) so that metal contacts metal. 

Environmental and operational limits are available in 

Appendix A: Specifications and Reference 

Data 

The loop should be designed so the terminal voltage does not drop below 10.5 Vdc when the 
transmitter output is set to 23 mA.

Namur Software Revision Number

SW

(1)

1.0.x - 1.4.x

(1)

Namur Software Revision: Located on the 
metal device tag

.

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments

Related manuals for Rosemount 2051

Kawai ES3 Specifications preview
ES3
Brand: Kawai Pages: 2
Datron 1061 Calibration And Servicing Handbook preview
1061
Brand: Datron Pages: 197
Kane 3500 Manual preview
3500
Brand: Kane Pages: 20
Balluff BML SL1-ALZ-ZZ Series Condensed Manual preview
BML SL1-ALZ-ZZ Series
Brand: Balluff Pages: 26
National Instruments NI 9421 Getting Started Manual preview
NI 9421
Brand: National Instruments Pages: 18
Watts HF scientific AccUView LED Owner'S Manual preview
HF scientific AccUView LED
Brand: Watts Pages: 40
Guru Home Systems GU-HB-201-R1 Installation Manual preview
GU-HB-201-R1
Brand: Guru Home Systems Pages: 20
Lennox Smart Air Quality Monitor Installation And Setup Manual preview
Smart Air Quality Monitor
Brand: Lennox Pages: 28
Roland KR-1070 Owner'S Manual preview
KR-1070
Brand: Roland Pages: 96
IFM AS-i CompactModule M8 Operating Instructions preview
AS-i CompactModule M8
Brand: IFM Pages: 4
THE ELECTRON MACHINE CORPORATION DSA E-Scan Operating And Service Manual preview
DSA E-Scan
Brand: THE ELECTRON MACHINE CORPORATION Pages: 32
Sagola Classic I 2 Instruction Manual preview
Classic I 2
Brand: Sagola Pages: 16
KEM RA-620 Operation Manual preview
RA-620
Brand: KEM Pages: 49
OTOVATION Amplitude T Series Installation Manual preview
Amplitude T Series
Brand: OTOVATION Pages: 15
Feasa ICT Series User Manual preview
ICT Series
Brand: Feasa Pages: 145
PCE Health and Fitness VT 3800 User Manual preview
VT 3800
Brand: PCE Health and Fitness Pages: 66
Farnell MarMonix MSL-765 User Manual preview
MarMonix MSL-765
Brand: Farnell Pages: 15
Shimadzu TOC-V CPH User Manual preview
TOC-V CPH
Brand: Shimadzu Pages: 22

Brands by name

Popular brands

Load more brands