manualshive.com logo in svg

Emerson Rosemount 2051, Reference Manual, Page: 187 / 228

Share
Download
Emerson Rosemount 2051 Reference Manual Download Page 187

177

Reference Manual 

00809-0100-4107, Rev BA

Appendix B: Product Certifications

April 2013

Product Certifications

E1

ATEX Flame-Proof
Certification No. KEMA 08ATEX0090X
Applicable Standards: EN60079-0:2009, IEC60079-0:2011, EN60079-1:2007, 
EN60079-26:2007
Markings 

 II 1/2 G 

Ex d IIC T6 Ga/Gb (–50 °C 

 Ta 

 65 °C)

Ex d IIC T5 Ga/Gb (–50 °C 

 Ta 

 80 °C)

IP66

1180

Ui = 32 Vdc

Special Conditions for Safe Use (X): 

1. Appropriate ex d blanking plugs, cable glands, and wiring needs to be suitable for a 
temperature of 90 °C.

2. This device contains a thin wall diaphragm. Installation, maintenance, and use shall 
take into account the environmental conditions to which the diaphragm will be 
subjected. The manufacturer’s instructions for maintenance shall be followed in detail to 
assure safety during its expected lifetime. 

3. In case of repair, Contact Emerson Process Management for information on the 
dimensions of flameproof joints.

ND

ATEX Dust
Certification No. Baseefa08ATEX0182X
Applicable Standards: EN60079-0:2012, EN 60079-31:2009
Markings: 

 II 1 D Ex t IIIC T50 °C T

500

 60 °C Da

IP66 IP68
U

i

 = 42.4 Vdc

 1180

Special Conditions for Safe Use (X): 

If the equipment is fitted with an optional 90 V transient suppressor, it is incapable of 
isolation from earth test and this must be taken into account during installation.

IECEx Certifications

I7

IECEx Intrinsic Safety 
Certification No. IECExBAS08.0045X
Applicable Standards: IEC60079-0:2011, IEC60079-11:2011
Ex ia IIC T4 Ga (–60 °C 

 T

a

 

 +70 °C)

Special Conditions for Safe Use (X): 

The device is not capable of withstanding the 500 V insulation test required by Clause 
6.3.12 of IEC60079-11. This must be taken into account when installing the apparatus.

Table B-5.  Input Parameters

U

i

 = 30 V

I

i

 = 300 mA

P

i

 = 1.3 W 

C

i

 = 0 μF

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments