Emerson Rosemount 2051 Reference Manual Download Page 156

Page: 156 / 228

146

Reference Manual

00809-0100-4107, Rev BA

Appendix A: Specifications and Reference Data

April 2013

Appendix A: Specifications and Reference Data

(4)

ATEX Flameproof, Intrinsic Safety, Type n, Dust

★

(4)

INMETRO Flameproof and Intrinsic Safety

★

FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5 and I5)

★

CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E6 and I6)

★

(4)

IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, Type n (combination of E7, I7, and N7)

★

(4)

ATEX and CSA Flameproof, Intrinsically Safe, Division 2

★

FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5, E6, I5,
and I6)

★

(4)

FM and ATEX Explosion-proof, Intrinsically Safe, Division 2

★

(4)

FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of E5, I5, E6, I6, E1, and I1)

★

(4)

ATEX Type n

★

(4)

IECEx Type n

★

(4)

ATEX Dust

★

Sensor Fill Fluid and O-ring Options
Standard

Standard

Inert Sensor Fill Fluid

★

Graphite-Filled (PTFE) O-ring

★

Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring

★

Display and Interface Options
Standard

Standard

(6)

LCD Display with Local Operator Interface

★

LCD Display

★

Transient Protection
Standard

Standard

(9)

Transient terminal block

★

Manifold for Remote Mount Option
Standard

Standard

3-Valve Manifold, Stainless Steel

★

5-Valve Manifold, Stainless Steel

★

Alarm Limit
Standard

Standard

(10)(11)

NAMUR Alarm and Saturation Levels, High Alarm

★

(10)(11)

NAMUR Alarm and Saturation Levels, Low Alarm

★

(10)

Custom Alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet)

★

(10)

Custom Alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet)

★

(10)

Low Alarm (standard Rosemount alarm and saturation levels)

★

PlantWeb Control Functionality
Standard

Standard

A01

(8)

OUNDATION

fieldbus Advanced Control Function Block Suite

★

Hardware Adjustments
Standard

Standard

(10)

Zero and Span Hardware Adjustments

★

(10)

Digital Zero Trim

★

Ground Screw
Standard

Standard

(12)

External Ground Screw Assembly

★

HART Revision Configuration
Standard

Standard

HR5

(10)

(13)

Configured for HART Revision 5

★

HR7

(10)

(14)

Configured for HART Revision 7

★

Typical Model Number: 2051CFC D C S 060 N 065 0 3 2 A A 1 WC E5 M5

Table 15. Rosemount 2051CFC Compact Flowmeter Ordering Information

★

The Standard offering represents the most common options. The starred options (

★

) should be selected for best delivery.

The Expanded offering is subject to additional delivery lead time.

Summary of Contents for Rosemount 2051





































































































































































































































Search results

Summary of Contents for Rosemount 2051

Reviews:

Emerson Rosemount 2051, Reference Manual, Page: 156 / 228

Search results

Summary of Contents for Rosemount 2051

Reviews: