manualshive.com logo in svg

Emerson Rosemount 2051, Reference Manual, Page: 25 / 228

Share
Download
Emerson Rosemount 2051 Reference Manual Download Page 25

15

Reference Manual 

00809-0100-4107, Rev BA

Section 2: Configure

April 2013

Configuration

Setting transmitter output with a Field Communicator

Setting transmitter output with AMS Device Manager 

Right click on the device and select 

Configure

.

1.

Click 

Manual Setup

 and choose output type from

 Analog Output Transfer Function 

and click 

Send

.

2. Carefully read the warning and click 

Yes

 if it is safe to apply the changes.

Setting transmitter output with a Local Operator Interface

Reference 

Figure 2-6 on page 15

 to select either linear or square root transfer function using the 

LOI. 

Figure 2-6. Set output with LOI

From the 

HOME

 screen, enter the fast key sequence 

Device Dashboard Fast Keys

2, 2, 1, 1, 6

EXTENDED MENU

CALIBRAT
DAMPING

TRANSFER FUNCT

TRANSFER FUNCT

SCALED VARIAB
ASSIGN PV
TAG
ALARM SAT 
VALUES
PASSWORD
SIMLATE
HART REV
BACK TO MENU
EXIT MENU

TRANSFER FUNCT

LINEAR TRANSFER 
FUNCTION
SQR ROOT TRANSFER 
FUNCTION
BACK TO MENU
EXIT MENU

VIEW CONFIG
ZERO TRIM
UNITS
RERANGE
LOOP TEST
DISPLAY

EXTENDED MENU

EXTENDED MENU

EXIT MENU

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments