manualshive.com logo in svg

Emerson Rosemount 2051, Reference Manual, Page: 43 / 228

Share
Download
Emerson Rosemount 2051 Reference Manual Download Page 43

Reference Manual 

00809-0100-4107, Rev BA

Section 3: Hardware Installation

April 2013

33

Hardware Installation

Section 3

Hardware Installation

Overview   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 33
Safety messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 33
Considerations   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 34
Installation procedures  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 35
Installation procedures  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 35
Rosemount 305, 306, and 304 Manifolds   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 47

3.1

Overview

The information in this section covers installation considerations for the Rosemount 2051 with 
HART protocols. A Quick Installation Guide (document number 00825-0100-4107) is shipped 
with every transmitter to describe recommended pipe-fitting and wiring procedures for initial 
installation. Dimensional drawings for each Rosemount 2051 variation and mounting 
configuration are included on 

page 38

. 

Note

For transmitter disassembly and reassembly refer to 

“Disassembly procedures” on page 89

, and 

“Reassembly procedures” on page 91

.

3.2

Safety messages

Procedures and instructions in this section may require special precautions to ensure the safety 
of the personnel performing the operation. Information that raises potential safety issues is 
indicated by a warning symbol ( ). Refer to the following safety messages before performing 
an operation preceded by this symbol.

Explosions could result in death or serious injury: 
Installation of this transmitter in an explosive environment must be in accordance with the 
appropriate local, national, and international standards, codes, and practices. Please review 
the approvals section of the Rosemount 2051 reference manual for any restrictions 
associated with a safe installation. 

Before connecting a Field Communicator in an explosive atmosphere, ensure the 
instruments in the loop are installed in accordance with intrinsically safe or 

non-incendive field wiring practices.

In an Explosion-Proof/Flameproof installation, do not remove the transmitter covers 

when power is applied to the unit. 

Process leaks may cause harm or result in death. 

Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads 
can cause electrical shock.

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments