manualshive.com logo in svg

Emerson FieldQ Q100, Product Data Sheet

Share
Download
Emerson FieldQ Q100 Product Data Sheet Download Page 54

Product data sheet

FieldQ

FieldQ

Copyright © Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website  

www.emerson.com/fieldq or from your Emerson Automation Solutions - Actuation Technologies Center: 

 

America’s: 

+1 281 477 4100 

Europe:

 +36 22 53 0950 

Asia/Pacific:

 +65 67 77 8211

1.606.06 Rev. 0 page 1 of 3
October 2017

FieldQ Valve Actuator

Full Stroke Adjustment Option

Description

FieldQ actuators with the Full Stroke Adjustment option are 
used where the maximum opening (or closing) position of the 
valve needs to be reduced, for instance to adjust the  

maximum flow capacity of a remote operated valve to 50%.

Operation

Full Stroke Adjustment screws (1) are fitted to both end caps and 

the screw length is such that adjustment is possible through the 
full outward stroke/rotation of the actuator.
Screwing in the Full Stroke Adjustment screws will reduce  
the  stroke.

Note: 

-  Only the outward stroke can be adjusted with the Full Stroke 

Adjustment screws.  
In case of assembly code CW, limit stop (3) is redundant.  
In case of assembly code CC, limit stop (2) is redundant.

-  For the inward stroke the standard limit stops can be used:
  -  Limit stop (2) for assembly code CW
  -  Limit stop (3) for assembly code CC

Rotation

Factory set: 

90°±0.5°. 

Adjustable range: 
(1) Full stroke adjustment screws: 

-3° to +93°

(2) Standard stroke adjustment screws: 

-3° to 15°

Sizing

Applying the stroke adjustment option will change the torque 
output level of spring return actuators depending on the 
amount of stroke adjustment. Please consult page 2 and the 

torque data sheets (1.602.02 Nm or 1.602.03 lbf.in) to define 

the torque output of a spring return actuator.

90°

0°

90°

0°

-3°

+15°

-3°

93°

Adjustable range: 
Full stroke adjustment 
screws (1)

Adjustable range:  
Standard stroke adjustment 
screws(2, 3)

1

2

3

1

96°

Len

gth

Fig. 1.  Reducing the flow throught the valve with full stroke 

adjustment option on the actuator.

Dimensions

The dimensions of the actuator remains the same except the 
length of the actuator due to the longer Full Stroke  
Adjustment screw (see table below).

Length Full stroke adjustment units at 90° rotation

Spring return

Double acting

mm

Inch

mm

Inch

QS0040

234

9.21

QD0040

175

6.89

QS0065

299

11.77

QD0065

208

8.19

QS0100

317

12.48

QD0100

231

9.09

QS0150

340

13.39

QD0150

257

10.12

QS0200

456

17.95

QD0200

313

12.32

QS0350

457

17.99

QD0350

332

13.07

QS0600

541

21.30

QD0600

417

16.42

QS0950

585

23.03

QD0950

456

17.95

QS1600

683

26.89

QD1600

562

22.13

Summary of Contents for FieldQ Q100



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands