Emerson Dixell XRB, Installing And Operating Instructions

Page: 18 / 38

1592038420 XRB30-60-70-77CH EN v1.1 2021.09.15 XRB 18/38
Label Description LT NT Level
AU2 2nd high temperature alarm 20.0 302 Pr2
AH2 2nd temperature alarm differential 2.0 4 Pr2
Ad2 2nd temperature alarm delay 0 0 Pr2
dA2 2nd temperature alarm delay at start-up 00:00 00:00 Pr2
bLL Compressor OFF due to 2nd low temperature alarm no no Pr2
AC2 Compressor OFF due to 2nd high temperature alarm no no Pr2
tbA Alarm relay deactivation yes yes Pr2
oA1 Relay output oA1 configuration CP1 CP1 Pr2
oA2 Relay output oA2 configuration Def Def Pr2
oA3 Relay output oA3 configuration Fan Fan Pr2
oA4 Relay output oA4 configuration LiG LiG Pr2
AoP Alarm relay polarity CL CL Pr2
ibt Base times for digital inputs min min Pr2
i1P Digital input 1 polarity CL CL Pr2
i1F Digital input 1 configuration nu nu Pr2
d1d Digital inputs 1 alarm delay (base time depends on par. ibt) 0 0 Pr2
i2P Digital input 2 polarity CL CL Pr2
i2F Digital input 2 configuration nu nu Pr2
d2d Digital inputs 2 alarm delay (base time depends on par. ibt) 0 0 Pr2
nPS
Number of external pressure switch alarms before stopping the
regulation
15 15 Pr2
OdC Compressor and fan status after door opening F-C F-C Pr2
rrd Regulation restart after door alarm no no Pr2
CLI Light output activation from door input no no Pr2
Lci Time with light output forced ON (0=function disabled) 0 0 Pr2
n01
Motion sensor detections before activating a light output (valid if ixF=EMt
and MSF=LiG or ALL)
5 5 Pr2
t01 Time with light output forced ON after motion detection 15 15 Pr2
MSF Function linked with the motion sensor nu nu Pr2
EMF
Motion sensor stop reading interval after switching off the light output by
button, serial command or energy saving algorithm (valid if ixF=EMt)
2 2 Pr2
ErA Energy saving algorithm Aut Aut Pr2
nbo
Number of virtual door openings of a single cell for energy saving
activation
3 3 Pr2
HES Temperature differential in energy saving 4.0 8 Pr2
LdE
Energy saving controls the lights (lights OFF when energy saving goes
active)
yes yes Pr2
Aid Period of analysis for ErA (valid if ErA=Aut) 1 1 Pr2
nCA Number of contiguous cells to activate energy saving (valid if ErA=Aut) 2 2 Pr2
nCC
Number of contiguous cells with energy saving for Set-Point variation
(valid if ErA=Aut)
4 4 Pr2
Pdt Automatic Pull Down activation after energy saving (1=30min) 1 1 Pr2
nEC
Maximum number of consecutives cells with energy saving activated
(valid only if ErA=Aut)
0 0 Pr2
nrC
Minimum number of consecutive cells in normal mode (valid only if
ErA=Aut)
0 0 Pr2
tUn System tuning: 0=low sensibility; 1=high sensibility Hi Hi Pr2
PPv
Temperature probe used by automatic energy saving algorithm (valid if
ErA=Aut)
P1 P1 Pr2
FEn
Force status change from energy saving mode to normal mode (valid if
ErA=Aut)
1 1 Pr2