Emerson CH Breaker Gateway Installation And Operation Manual Download Page 20 | Manualshive

Page: 20 / 22

background image

Appendix B: Troubleshooting

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

Board Offline

I/O Network Problems

Check wiring polarity. Verify the
485+ uses one color and the 485-
uses the other color throughout
the network.

Check each connector for any
loose wires or frayed strands
between connectors.

Termination Jumpers Set Incor-
rectly

Verify all three jumpers are set in
the UP position if the board is at
the end of a daisy chain, and that
all other boards are not termi-
nated (jumpers in DOWN posi-
tion).

Board Not Receiving Power

Refer to

Figure 3-1

for the fol-

lowing steps:
1. Verify proper transformer wir-
ing. Check that the 28 VAC sec-
ondary switch is in the ON
position.

2. Verify that the secondary
power is 28 VAC and the wires
are connected properly.

3. Check Fuses F5 and F6.

4. Verify line voltage is con-
nected to high-line side of the
control power transformer.

Dip Switches Set Incorrectly

Check 8RO address, 16AI
address, and baud rate settings.
Refer to

Section 4.2.1.,

Gateway

Board Numbering

and

Section

4.2.2.,

Setting the Baud Rate Dip

Switches

.

Note: after changing dip switch
settings, cycle power to board
using the 28 VAC secondary
power switch (flip to the OFF
position and then to the ON posi-
tion).

«
...
18
19
20
21
22
»

Summary of Contents for CH Breaker Gateway























Reviews:

No comments

Related manuals for CH Breaker Gateway

Brand: MRS Pages: 21

Brand: San Telequip Pages: 19

Brand: Hoymiles Pages: 2

Brand: TRBOnet Pages: 33

Brand: TANDBERG Pages: 54

Brand: ADI Pages: 56

Brand: Z-Wave Pages: 68

Brand: RTA Pages: 74

Brand: ViewSonic Pages: 65

Brand: Alpha Telecom Pages: 43

Brand: ZyXEL Communications Pages: 477

OfficeConnect 3CRWE53172

Brand: 3Com Pages: 124

OCG VOICE EXPANSION -

Brand: 3Com Pages: 177

Brand: ZyXEL Communications Pages: 2

Brand: ZyXEL Communications Pages: 2

bigpond velocity

Brand: Telstra Pages: 13

Brand: Schlage Pages: 60

Brand: Viola Systems Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands