Emerson CH Breaker Gateway Installation And Operation Manual Download Page 11

Page: 11 / 22

REFLECS

Site Controller Software Setup • 5

4.2.3. Setting the RS485 I/O Termi-

nation Jumpers

As part of a site controller’s RS485 I/O (COM A or

COM D) Network, a Gateway must be terminated if it is the

end device of a daisy chain. Refer to the controller’s user

manual for information about daisy chain networks and
how they are terminated.

To terminate the Gateway, set the I/O Network Jumpers

to the RIGHT position as shown in

Figure 4-8

. To unter-

minate the Gateway, set the jumpers to the LEFT position.

Site Controller Soft-

ware Setup

5.1.

REFLECS

For backwards compatibility with REFLECS, the CH

Breaker Gateway behaves on the network identically to

16AI and 8RO boards. These devices should be set up and
addressed in the same way I/O boards are set up. Refer to

your controller’s manual for set up instructions.

5.2.

E2 and Einstein

5.2.1. Board and Application Setup

Set up the number of boards on the I/O Network from

the Connected I/O screen. Press the

key to open the

Main Menu and press:

System Configuration

Network Setup

Connected I/O Boards and Controllers

If using an Einstein controller, from the Main Status/

Home screen, press

(

(Actions),

Network Status/

Setup, and then

Connected I/O Boards & Controllers.

Add as many 16AIs and 8ROs as is necessary to cover

the entire Start-End range chosen in

Section 4.2.1.,

Gate-

way Board Numbering

. Press

to save and exit.

Figure 4-7

- Dip Switch Setting for Numbering Gateway

Figure 4-8

- Gateway RS485 I/O Network Termination

GATEWAY

DIP SWITCH

I/O NETWORK OR
COM A AND D
BAUD RATE

I/O NET BAUD RATE SETTINGS

9600

19200

Figure 5-1

- Connected I/O Boards Screen

Summary of Contents for CH Breaker Gateway























Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands

Emerson CH Breaker Gateway, Installation And Operation Manual

Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands