Emerson CH Breaker Gateway Installation And Operation Manual Download Page 14

Page: 14 / 22

8 • CH Breaker Gateway I&O Manual

026-1710 Rev 1 05-15-07

6.1.1. HHT Screens

The Home screen is the first screen that appears. Press

F1 at any time to return to the Home screen.

Press the down arrow key to move to the Starting Board

Addresses screen.

Next, arrow down to the Option screen.

6.1.2. Configuration

Use the left or right arrows to activate the

OPTION:

field and choose

to start configuring each Panel’s break-

ers to groups. Press DOWN ARROW to move to the next
screen.

From this screen you can begin assigning breakers on

panels 1 through 4 to breaker groups. Refer to

Table A-1

for a diagram of the breaker panel and the breaker number
to group assignment.

Use the number keys to enter the group number.

Change the group number to the group you want to associ-
ate the breaker with (a maximum number of 48).

Press DOWN ARROW to scroll through all 48 break-

ers on each of the four panels and set the group numbers as
you scroll through the breakers.

HHT Keys

Function

Home screen key

Quick access to status information

Left and right arrow keys point to
the desired field to be configured

Up and down arrow keys scroll

through all breakers on panel
screens

Cancel

Deletes number you have chosen
and changes it to zero, and cancels

overrides on selected field

Enter

Saves changes (optional - use the
down arrow)

Toggles between override ON and
OFF

Toggles between override ON and

OFF

Table 6-1

- HHT Key Functions

Figure 6-1

- Home Screen

Figure 6-2

- Starting Board Addresses Screen

CPC CH ModBus GW
810-3722

(PRESS )

VER: 1.11F01

#of Brk Grps: 2

ADDR Start End
16AI 1 - 1
8RO 1 - 1

Figure 6-3

- Option Screen

Option No.

Function

Status information that can be
overridden. (An asterisk "*" sig-
nifies a proof failure)

Diagnostics for troubleshooting

Configuration settings

Table 6-2

- Option Choices Chart

Figure 6-4

- Panel 1 Breakers to Group Screen

NOTE: If a breaker is assigned to a group
that is not set up, a proof failure message will
occur.

OPTION: 0

1= STATUS

2= DIAGS
3= CONFIG

PANEL 1

BRK 1 GRP 1
BRK 2 GRP 1
BRK 3 GRP 1

Summary of Contents for CH Breaker Gateway























Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands

Emerson CH Breaker Gateway, Installation And Operation Manual

Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands