Emerson CH Breaker Gateway Installation And Operation Manual Download Page 21

Page: 21 / 22

HHT Home screen displays
FAIL: I/O NET.

Red Alarm Status LED is blink-
ing once per second.

I/O Net Status LED is not blink-
ing.

Communication has been lost
between the site controller and
the Gateway.

Check I/O Net wiring.

Check that 16AI and 8RO
addresses are set with the HHT,
and boards are defined in the site
controller.

HHT Home screen displays
FAIL: COMM BUS.

The red Alarm Status LED is on
solid.

The Gateway is not configured
with at least one group. It must
be configured before the Gate-
way will communicate with the
PRC100MODs on the MOD-
BUS Network.

Communication has been lost
between the Gateway and the
PRC100MOD(s).

If Receiver Bus Status LED is
not blinking, assign at least one
breaker to a group (1-16). If the
Group number is 0 (zero), it is
undefined.

If Receiver Bus Status LED is
blinking rapidly, check MOD-
BUS wiring and PRC100MOD
addressing.

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

Summary of Contents for CH Breaker Gateway























Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands

Emerson CH Breaker Gateway, Installation And Operation Manual

Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands