Emerson CH Breaker Gateway Installation And Operation Manual Download Page 8

Page: 8 / 22

2 • CH Breaker Gateway I&O Manual

026-1710 Rev 1 05-15-07

The Gateway should be mounted in an environment

with ambient temperature between -40°F and 150°F, with a

non-condensing relative humidity between 5% and 95%.

Gateway boards are not supplied with an enclosure but

come with a snap-track for easy installation. The insulation

sheet and I/O board must be removed from the track before
the track is mounted. The snap-track is mounted using the

0.1875” mounting slots.

Figure 2-2

shows this installation

procedure.

Power Wiring

3.1.

CH Breaker Gateway Power
Wiring

The Gateway requires 24VAC power from a Class 2

center-tapped

transformer.

CPC supplies several sizes of center-tapped transform-

ers for powering multiple 16AIs, 8ROs, and other RS485

peripheral boards of the E2, Einstein, and REFLECS sys-

tems.

Refer to your controller’s user manual for information

on how to use the center-tapped transformers listed in

Ta-

ble 3-1

to power multiple RS485 I/O devices for the US and

Canada.

Figure 3-1

shows how to connect the 56VA and 80VA

transformers to the Gateway power connector.

Figure 2-1

- Gateway Board Mounting Dimensions

Figure 2-2

- Snap-Track Installation

Input Voltage

24VAC, Class 2, 50/60Hz

Power

5VA

Table 3-1

- Gateway Power Requirements

Three-Board

Six-Board

P/N

640-0056

640-0080

Power Rating

56 VA

80 VA

Table 3-1

-US and Canada Power Ratings for CPC Transformers

Figure 3-1

- Pinout for the 56VA (640-0056) and 80VA (640-

0080) Transformers

Summary of Contents for CH Breaker Gateway























Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands

Emerson CH Breaker Gateway, Installation And Operation Manual

Search results

Summary of Contents for CH Breaker Gateway

Reviews:

Related manuals for CH Breaker Gateway

Brands by name

Popular brands