Emerson Bettis RTS FQ Series Operating Manual Download Page 11 | Manualshive

Page: 11 / 91

background image

6

Section 3: General

User Instructions

MAN-02-04-60-0351-EN Rev. 3

Febraury 2019

General

3.6

Protective Devices

3.6.1 Torque

Bettis RTS FQ Fail-Safe Quarter-Turn actuators provide electronic torque monitoring.
The switch-off torque can be modified in the controller menu for each direction separately.
By default, switch-off torque is set to the ordered value. If no torque was specified with the
order, the actuator is supplied from the factory with the maximum configurable torque.

For more information, see Section 8.1.

3.6.2 Motor Temperature

All ACTUSMART CM actuators are normally equipped with motor winding temperature
sensors, which protect the motor against excessive winding temperature.
The display will show the corresponding error upon exceeding the permissible motor
temperature, see Section 13.1.

3.6.3 Input Fuse, Thermal Fuse

The frequency inverter is protected by an input fuse and the explosion proof version by a
thermal fuse. If one of the fuses releases, a serious defect occurs and the frequency inverter
must be replaced.

3.7

Ambient Temperature

Unless otherwise specified upon ordering, the following operating temperatures apply:

•

On/Off duty (open-loop control) -25 to +60C

•

Modulating duty (closed-loop control) -25 to +60C

•

Explosion-proof version -20 to +40C (acc. EN 60079-0)

•

Explosion-proof version with extended temperature range -40 to +60C

«
...
9
10
11
12
13
...
»

Summary of Contents for Bettis RTS FQ Series




























































































Reviews:

No comments

Related manuals for Bettis RTS FQ Series

Brand: ABB Pages: 63

Brand: Kasco Pages: 3

Brand: C Prox Ltd Pages: 5

Brand: FAAC Pages: 32

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: GCE Pages: 24

Brand: Hama Pages: 12

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Brand: Hama Pages: 8

Brand: Samson Pages: 2

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: Rabe Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands