Emerson 01100017 Quick Start Manual Download Page 53

Page: 53 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

OI.br

Braking IGBT over current
detected: short circuit protection
for the braking IGBT activated

Over current has been detected in braking IGBT or braking
IGBT protection has been activated.
Possible cause:
•

Check brake resistor wiring

•

Check braking resistor value is greater than or equal to the
minimum resistance value

•

Check braking resistor insulation

OI.SC

Output phase short-circuit

Over-current detected on drive output when enabled.

OPt.d

Option module does not
acknowledge during drive mode
changeover

Option module did not acknowledge notifying the drive that
communications with the drive has been stopped during the
drive mode changeover within the allocated time.

Out.P

Output phase loss detected

Phase loss has been detected at the drive output.

DC bus voltage has exceeded the
peak level or maximum continuous
level for 15 seconds

The

trip indicates that the DC bus voltage has exceeded the

maximum limit.
Possible solutions:
•

Increase

Deceleration Rate 1

(Pr

00.004

)

•

Decrease the braking resistor value (staying above the
minimum value)

•

Check nominal AC supply level

•

Check for supply disturbances which could cause the DC
bus to rise

•

Check motor insulation using a insulation tester

P.dAt

Power system configuration data
error

Contact the supplier of the drive.

Pb.bt

Power board is in bootloader mode Power board is in bootloader mode

Pb.Er

Communication has been lost /
errors detected between power
control

Communications loss between power and control.

Pb.HF

Power board HF

Power processor hardware fault - contact the supplier of the
drive

Pd.S

Power down save error

Error has been detected in the power down save parameters
saved in non-volatile memory.

PH.Lo

Supply phase loss

The drive has detected an input phase loss or large supply
imbalance.

PSU

Internal power supply fault

One or more internal power supply rails are outside limits or
overloaded.

r.ALL

RAM allocation error

Option module derivative image has requested more parameter
RAM than is allowed.

r.b.ht

Hot rectifier/brake

Over-temperature detected on input rectifier or braking IGBT.

Measured resistance has
exceeded the parameter range

The measured stator resistance during an autotune test has
exceeded the maximum possible value of

Stator Resistance

Refer to the

Drive User Guide

SCL

Control word watchdog has timed
out

The control word has been enabled and has timed out

SL.dF

Option module in option slot 1 has
changed

Option slot 1 on the drive is a different type to that installed
when parameters were last saved on the drive.

SL.Er

Option module in option slot 1 has
detected a fault

Option module in option slot 1 on the drive has detected an
error.

SL.HF

Option module 1 hardware fault

Option slot 1 on the drive has indicated a hardware fault.

SL.nF

Option module in option slot 1 has
been removed

The option module in option slot 1 on the drive has been
removed since the last power up.

SL.tO

Option module watchdog function
service error

The option module installed in Slot 1 has started the option
watchdog function and then failed to service the watchdog
correctly.

Trip

code

Condition

Description

Unidrive M200 201 Quick Start Guide English Iss6.book Page 53 Thursday, September 10, 2015 1:48 PM

Summary of Contents for 01100017































































Search results

Summary of Contents for 01100017

Reviews:

Related manuals for 01100017

Brands by name

Popular brands

Emerson 01100017, Quick Start Manual

Search results

Summary of Contents for 01100017

Reviews:

Related manuals for 01100017

Brands by name

Popular brands