Emerson 01100017 Quick Start Manual Download Page 32

Page: 32 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

6.2 Unidrive M200/201 parameter descriptions

Key:

Set Pr

00.001

at the required minimum output frequency of the drive for both directions of rotation.

The drive speed reference is scaled between Pr

00.001

and Pr

00.002

. Pr

00.001

is a nominal value;

slip compensation may cause the actual frequency to be higher. When the drive is jogging, Pr

00.001

has no effect.

Set Pr

00.002

at the required maximum output frequency for both directions of rotation. The drive

speed reference is scaled between Pr

00.001

and Pr

00.002

. Pr

00.002

is a nominal value; slip

compensation may cause the actual frequency to be higher. The drive has additional over-speed
protection.

Set Pr

00.003

at the required rate of acceleration. Note that larger values produce lower

acceleration. The rate applies in both directions of rotation.

Read /
Write

Read
only

Num

Number
parameter

Bit

Bit
parameter

Txt

Text string Bin

Binary
parameter

Filtered

No
default
value

Not
copied

Protected
parameter

Rating
dependent

User save

Power-down
save

DE Destination

00.001 {01.007}

Minimum Reference Clamp

Num

VM_NEGATIVE_REF_CLAMP1 Hz

0.00 Hz

RFC-A

00.002 {01.006}

Maximum Reference Clamp

Num

VM_POSITIVE_REF_CLAMP Hz

50.0 Hz default: 50.00 Hz
60.0 Hz default: 60.00 Hz

RFC-A

00.003 {02.011}

Acceleration Rate 1

Num

VM_ACCEL_RATE s/100 Hz

5.0 s/100 Hz

RFC-A

Unidrive M200 201 Quick Start Guide English Iss6.book Page 32 Thursday, September 10, 2015 1:48 PM

Summary of Contents for 01100017































































Search results

Summary of Contents for 01100017

Reviews:

Related manuals for 01100017

Brands by name

Popular brands

Emerson 01100017, Quick Start Manual

Search results

Summary of Contents for 01100017

Reviews:

Related manuals for 01100017

Brands by name

Popular brands