Emerson 01100017 Quick Start Manual Download Page 46

Page: 46 / 62

Unidrive M200-201 Quick Start Guide

Issue Number: 6

Defines the post-brake release delay.

Defines the initial direction of the brake.

See Brake Controller Brake Release in

Drive User Guide

Defines if the brake is applied through zero threshold. See Brake Controller Brake Release in

Drive

User Guide

00.051 {12.047}

Brake Controller Post-brake Release Delay

Num

0.0 to 25.0 s

1.0 s

RFC-A

00.053 {12.047}

Brake Controller Initial Direction

Txt

Ref (0), For (1), Rev (2)

Ref (0)

RFC-A

Value

Text

reF

For

Rev

00.054 {12.051}

Brake Controller Brake Apply Through Zero Threshold

Num

0.00 to 25.00 Hz

0.00 Hz

RFC-A

00.055 {12.041}

Brake Controller Enable

Txt

dis (0), Relay (1), dig IO (2), User (3)

dis (0)

RFC-A

Value

Text

Dis

Relay

dig IO

USEr

Unidrive M200 201 Quick Start Guide English Iss6.book Page 46 Thursday, September 10, 2015 1:48 PM

Summary of Contents for 01100017































































Search results

Summary of Contents for 01100017

Reviews:

Related manuals for 01100017

Brands by name

Popular brands

Emerson 01100017, Quick Start Manual

Search results

Summary of Contents for 01100017

Reviews:

Related manuals for 01100017

Brands by name

Popular brands