manualshive.com logo in svg

ELTEX TAU-4.IP, Operation Manual, Page: 28 / 190

Share
Download
ELTEX TAU-4.IP Operation Manual Download Page 28

 

28

 

VoIP Subscriber Gateways 

 

If 

Manual

  mode  is  selected,  the  client’s  public  address  is  set  manually  via  the 

NAT  Address

 

parameter (the address must be entered in IPv4 format). 

To store changes to the operative memory of the device, click the 

Save Changes button.

 To store 

settings into the non-volatile memory, click 

Apply

 button.

 

2.1.4 The ‘Configuration’ submenu 

In the ‘Configuration’ submenu, you may save the current configuration, restore and reset it to 

the default settings. 

 

Backup Configuration: 

-

 

To save the current configuration of the device to a local PC, click 

‘Backup’

 button.

 

Restore Configuration: 

-

 

Saved  config.tgz  file

  –  configuration  file  selection.  To  restore  previous  established 

configuration, click 

‘Restore’

 button.

 

Reset to default configuration

 – reset to the default configuration via pressing 

‘Reset’

 button.

 

 

After  the  reset,  the  access  to  the  device  is  possible  via  IP  address  getting  from  DHCP 
interface. If DHCP server is absent, use gateway voice menu. In order to do that,  connect 
phones to any FXS port and dial ‘***’ first, then dial ‘0’. 192.168.1.2  -  IP address will be 
assigned to the device automatically. This address will be active to the first reboot of the 
gateway. 

 

 

 

Summary of Contents for TAU-4.IP































































































































































































Reviews:

No comments