ELTEX TAU-4.IP Operation Manual Download Page 139

Page: 139 / 190

139

VoIP Subscriber Gateways

interval

<value>

int:10-3600

priv

Set registration time,
in seconds

Set the
default reregistration
time(default: 300)

domain

<value>

priv

Set SIP domain

Do not use SIP domain

domain_to_reg

priv

Allow the use of SIP
domain during
registration on SIP
server

Deny the use of SIP
domain during
registration on SIP
server

expires

<value>

priv

Set reregistration
time on SIP server, in
seconds

Set the default
reregistration time on
SIP server (default:
1800)

codec

priv

list

<value>

The  list  of  voice  codecs
separated  by  ‘space’
character
g729a,  g729b,  g729x,
g711a,  g711u,  g723,
g726_24, g726_32

priv

Voice codec list by
priority

ptime

Value1: g729, g711,
g723,

g726_24,

g726_32
value2: 10-120

priv

Set packetization
time for voice codecs
(ms)

Set the default
packetization time
(default: g729 – 20ms,
g711 – 20ms, g723 –
30ms, g726_24 – 20ms,
g726_32 – 20ms)

dtmfmode

priv

Set the default dialing
signaling method
(Default: Inband)

inband

priv

Use inband digit
transfer of extension
dialing in RTP voice
packets

rfc2833

priv

Use digit transfer of
extension dialing
according to
RFC2833 as

Summary of Contents for TAU-4.IP































































































































































































Search results

Summary of Contents for TAU-4.IP

Reviews:

ELTEX TAU-4.IP, Operation Manual, Page: 139 / 190

Search results

Summary of Contents for TAU-4.IP

Reviews: