manualshive.com logo in svg

ELTEX TAU-4.IP, Operation Manual, Page: 136 / 190

Share
Download
ELTEX TAU-4.IP Operation Manual Download Page 136

 

136

 

VoIP Subscriber Gateways 

 

configuration is 
performed via DHCP  

on the WAN port 

 

 

 

dhcp_gateway   

 

 

- 

priv 

Apply DHCP option 3 
received from DHCP 

Do not apply DHCP 
option 3 received from 
DHCP 

 

 

 

dhcp_dns 

 

 

 

- 

priv 

Apply DHCP option 6 
received from DHCP 

Do not apply DHCP 
option 6 received from 
DHCP 

 

 

 

dns 

<value> 

 

 

IP address 

priv 

Configures IP 
address of the first 
external DNS 

Set the default DNS 
address (Default: 
192.168.1.1) 

 

 

 

dns2 

<value> 

 

 

IP address 

priv 

Configures IP 
address of the 
second external DNS 

Set the default second 
DNS address (Default: 
192.168.1.1) 

 

 

 

dscp 

.. 

 

 

.. 

 

 

 

 

 

 

 

signaling 

<value> 

 

int:0-63 

priv 

Set DSCP tag for SIP 
message 
transmission  

Set the default DSCP 
tag value (default: 26) 

 

 

 

 

media 

<value> 

 

int:0-63 

priv 

Set DSCP tag for 
RTP/RTCP traffic 
transmission 

Set the default DSCP 
tag value (default: 46) 

 

 

 

gateway 

<value> 

 

 

IP address 

priv 

Set the default 
gateway address 

Set the default gateway 
address (Default: 
192.168.1.1) 

 

 

 

ipaddr 

<value> 

 

 

IP address 

priv 

Set network 
interface IP address 

Set the default IP 
address of network 
interface (Default: 
192.168.1.2) 

 

 

 

netmask 

<value> 

 

 

netmask 

priv 

Set the subnet mask  Set the default value of 

subnet mask (default: 
255.255.255.0) 

 

 

 

ntp 

.. 

 

 

.. 

priv 

 

 

 

 

 

 

enable 

 

 

- 

priv 

Enables NTP 

Disables NTP 

 

 

 

 

ipaddr 

<value> 

 

address 

priv 

Set a remote server  Set the default value of 

Summary of Contents for TAU-4.IP































































































































































































Reviews:

No comments