ELTEX TAU-4.IP Operation Manual Download Page 157

Page: 157 / 190

157

VoIP Subscriber Gateways

Example

tau-8# show proc

PID USER VSZ STAT COMMAND

1 admin 1504 S init [

2 admin 0 SW< [kthreadd]

3 admin 0 SWN [ksoftirqd/0]

4 admin 0 SW< [watchdog/0]

5 admin 0 SW< [events/0]

...

show history

The command is intended for viewing CLI commands history.

Syntax

show history

Parameters

Command contains no arguments.

Privilegy

priv

Command mode

EXEC

Example

tau-8# show history

4 show voiceport statistic

8 show voiceport statistic 1

9 show voiceport status 1

11 show voiceport configuration 1

12 show voiceprofile 1

enable

The command is intended to enable the privilege mode.

Syntax

enable

Parameters

Command contains no arguments.

Privilegy

none

Command mode

EXEC

Example

tau-8> enable

Summary of Contents for TAU-4.IP































































































































































































Search results

Summary of Contents for TAU-4.IP

Reviews:

ELTEX TAU-4.IP, Operation Manual, Page: 157 / 190

Search results

Summary of Contents for TAU-4.IP

Reviews: