ELTEX TAU-4.IP Operation Manual Download Page 169

Page: 169 / 190

169

VoIP Subscriber Gateways

Sets the default factory IP address of the gateway (default: 192.168.1.1).

Example

tau-8(config-net)# gateway 192.168.118.99

ipaddr

Sets the IP address of network interface.

Syntax

ipaddr <value>

Parameters

<value> - IP address

Privilegy

priv

Command mode

CONFIG-NETWORK

Negotiation function 'no' command

Sets the factory IP address of network interface (default: 192.168.1.2).

Example

tau-8(config-net)# ipaddr 192.168.118.9

netmask

Sets a subnet.

Syntax

netmask <value>

Parameters

<value> - IP address

Privilegy

priv

Command mode

CONFIG-NETWORK

Negotiation function 'no' command

Sets the factory settings of subnet mask (default: 255.255.255.0).

Example

tau-8(config-net)# netmask 255.255.255.0

ntp enable

Enables the NTP protocol (default: disabled).

Syntax

ntp enable

Parameters

Command contains no arguments.

Privilegy

Summary of Contents for TAU-4.IP































































































































































































Search results

Summary of Contents for TAU-4.IP

Reviews:

ELTEX TAU-4.IP, Operation Manual, Page: 169 / 190

Search results

Summary of Contents for TAU-4.IP

Reviews: