ELTEX TAU-4.IP Operation Manual Download Page 173

Page: 173 / 190

173

VoIP Subscriber Gateways

Negotiation function 'no' command

Sets the factory value for the password contained in traps (default: trap).

Example

tau-8(config-net)# snmp trapcomm testtrap

telnet

Enables access to the device via the telnet protocol.

Syntax

telnet

Parameters

Command contains no arguments.

Privilegy

priv

Command mode

CONFIG-NETWORK

Negotiation function 'no' command

Deny the access to the device via telnet protocol.

Example

tau-8(config-net)# telnet 192.168.1.7

ssh

Enables access to the device via the SSHv2 protocol.

Syntax

ssh

Parameters

Command contains no arguments.

Privilegy

priv

Command mode

CONFIG-NETWORK

Negotiation function 'no' command

Deny the access to the device via SSHv2 protocol.

Example

tau-8(config-net)# ssh 192.57.2.6

web enable

Enables access to the device via HTTP and HTTPS.

Syntax

web enable

Parameters

Command contains no arguments.

Summary of Contents for TAU-4.IP































































































































































































Search results

Summary of Contents for TAU-4.IP

Reviews:

ELTEX TAU-4.IP, Operation Manual, Page: 173 / 190

Search results

Summary of Contents for TAU-4.IP

Reviews: