ELTEX TAU-4.IP Operation Manual Download Page 132

Page: 132 / 190

132

VoIP Subscriber Gateways

port

<value>

int:1-65535

none

UDP port number for
UDP datagram
transmission
(default: 33434)

size

<value>

int:40-32768

none

Overall length of
traceroute packets,
in bytes
(default:100)

show

none

system

none

Displays the
Firmware version

hwaddr

none

Displays the current
MAC address

ipaddr

none

Displays the current
IP address

netmask

none

Displays the current
netmask

network

none

Displays network
interface
configurations

version

none

Displays the device
configuration
versions

voiceport

none

status

<value>

int:1-8

none

Displays FXS port
status

configuration

<value>

int:1-8

priv

Displays FXS port
configuration

enable

none

Enables privileged
mode

disable

priv

Disables privileged

Summary of Contents for TAU-4.IP































































































































































































Search results

Summary of Contents for TAU-4.IP

Reviews:

ELTEX TAU-4.IP, Operation Manual, Page: 132 / 190

Search results

Summary of Contents for TAU-4.IP

Reviews: