ELTEX TAU-4.IP Operation Manual Download Page 144

Page: 144 / 190

144

VoIP Subscriber Gateways

ms (Default: 600)

hybrid

priv

Set hybrid
parameters

<value>

int:-230-20

priv

Set a gain factor
value of terminating
set at the reception,
dB

Set the default value
(default: -70)

<value>

int:-170-60

priv

Set a gain factor
value of terminating
set at the
transmission, dB

Set the default value
(default: 0)

profile

priv

name

<value>

str:96 sym

priv

Set FXS profile name Set the default FXS

profile name (Default:
Default)

stopdial

priv

Enable option that
completes dialing by
entering # character

Disable option that
completes dialing by
entering # character

timer

...

duration

<value>

Int:0-60

Set a timer value for
dialing, ms

Set the default timer
value for dialing, ms
(default: 30)

waitanswer

<value>

Int:0-120

Set an answer timer
value

Set the default answer
timer value, ms
(Default: 30)

tunnel

<value>

0 - Internet
1 = VoIP
2 - Management

Allows to execute
root mode
commands from any
other command-line
interface mode

exit

Exit configuration

Summary of Contents for TAU-4.IP































































































































































































Search results

Summary of Contents for TAU-4.IP

Reviews:

Related manuals for TAU-4.IP

Brands by name

Popular brands

ELTEX TAU-4.IP, Operation Manual

Search results

Summary of Contents for TAU-4.IP

Reviews:

Related manuals for TAU-4.IP

Brands by name

Popular brands