Elpro Technologies CONDOR 415U-1 Series Configuration Manual Download Page 38

Page: 38 / 41

User Manual

Condor 415U-1-Cx Battery Powered Wireless IO

Version 1.4

●

Channel Spacing: 6.25, 12.5, 25kHz (software configurable, 6.25 not available in C9)

●

Data Rate Raw @ 6.25, 12.5, 25kHz (6.25 not available in C9)

6.25Khz 12Khz

25Khz

▪

QPSK-FEC:

4 kbps

8 kbps

16 kbps

▪

QPSK:

8 kbps

16 kbps

32 kbps

▪

16-QAM:

16 kbps

32 kbps

64 kbps

▪

64-QAM:

24kbps

48 kbps

96 kbps

●

Typical Range (LoS) - 50km+ (62 miles)

Compliance

●

Regulatory

▪

Australia: RCM

▪

Europe: CE/RED

▪

USA: FCC

▪

Canada: IC

●

EMC: FCC CFR47 Part 15; EN 301 489-3; EN 301 489-5

●

RF (radio): FCC CFR47 Part 90; IC RSS 119; EN 300 113; EN 300 220; AS/NZS4295; AS/NZS4268

●

Safety: EN/IEC/UL 62368

●

Hazardous Area: UL Class I Div 2 (RF Power 2W EIRP)

Power Supply

●

Supply/Solar - 17-30 Vdc, under/rev voltage protection, Ext Battery - 11-15Vdc into battery
connection terminal.

●

Battery Options

▪

Internal (LFP rechargeable) Lithium Iron Phosphate LiFePO.

▪

Internal (LiP non-rechargeable) Lithium Thionyl Chloride LiSOCI2.

▪

External 12Vdc, Lead acid or Lithium Iron Phosphate LiFePO, charge current max 2A

●

Solar Regulator or Battery Charger

▪

External power supply/solar panel charges internal lithium iron phosphate or
external lead acid battery

▪

Smart charger up to 2A charge current MPPT optimised for 5-30W solar panel

●

Idle Current draw: 120µA @ 13V

●

Transmit current Draw (max): 2.5A @ 13.8V (10W RF), 1.2A @ 24V (10W RF)

General

●

Size: 190mm x 197mm x 98mm

(7.5” x 7.8” x 3.8”)

●

Housing: Aluminum cast enclosure with removable door IP66 rated

●

Mounting: Panel mount standard (DIN rail, pole, or solar mount options)

●

Operating Temperature

▪

external supply -40 to 70°C (-40 to 158°F)

▪

LFP rechargeable battery

-20 to 60°C (-4 to 140°F)

▪

LiP non-rechargeable battery -40 to 70°C (-40 to 158°F)

●

Humidity Rating: - 0-99% RH noncondensing

●

Cable Entry: Standard M20 cable gland 5-13mm cable diameter UL/VDE, Accessory option M20 to

½”NPT

Conduit Adaptor

●

Weight: 1.8 kg (4.0lb)

–

not including internal battery

●

Altitude: 0-2000m (0-8000ft)

●

Pollution Degree: 4

Summary of Contents for CONDOR 415U-1 Series










































Search results

Summary of Contents for CONDOR 415U-1 Series

Reviews:

Related manuals for CONDOR 415U-1 Series

Brands by name

Popular brands

Elpro Technologies CONDOR 415U-1 Series, Configuration Manual

Search results

Summary of Contents for CONDOR 415U-1 Series

Reviews:

Related manuals for CONDOR 415U-1 Series

Brands by name

Popular brands