Elmo 1/100 Installation Manual Download Page 72

Page: 72 / 88

Gold Twitter Installation Guide

MAN-G-TWI (Ver. 2.000)

|EtherCAT Module|

www.elmomc.com

Table of Contents

10.5.1.2.

ECT1 connector

Pin (ECT1)

Signal

Function

PHY

EtherCAT OUT RX+ Line

PHY

EtherCAT OUT TX+ Line

PHY_OUT_RX-

EtherCAT OUT RX- Line

PHY_OUT_TX-

EtherCAT OUT TX- Line

EtherCAT IN/Ethernet RX+ Line

EtherCAT IN/Ethernet TX+ Line

PHY_IN_RX-

EtherCAT IN/ Ethernet RX- Line

PHY_IN_TX-

EtherCAT IN/Ethernet TX- Line

Table 11: Connector ECT1

Note:

EtherCAT IN port can be configured to an Ethernet Port.

Note: Always use CAT5e cables.

10.5.1.3.

ECT3 Connector

Pin (ECT3)

Signal

Function

SB_Clock Serial Bus_Clock (9.375Mhz) for extended IO (refer to the MAN-

G-Panel Mounted Drives Hardware Manual)

SB_Load

Serial Bus Load for extended IO
(refer to the MAN-G-Panel Mounted Drives Hardware Manual)

Table 12: Connector ECT3

10.5.1.4.

3.3V Connector

Pin

Signal

Function

3.3V

3.3 V supply voltage for EtherCAT LEDs

3.3V

3.3 V supply voltage for EtherCAT LEDs

Table 13: 3.3V Connector

Summary of Contents for 1/100

























































































Search results

Summary of Contents for 1/100

Reviews:

Brands by name

Popular brands

Elmo 1/100, Installation Manual

Search results

Summary of Contents for 1/100

Reviews:

Brands by name

Popular brands