Electrolux W4300H Service Manual Download | Manualshive

Page: 120 / 140

background image

120

Troubleshooting

Error code 15, EMERGENCY STOP

This error code is generated by the CPU board. The error code arises if the
emergency stop switch has been activated on the machine.
The cause can be inadvertent activation of the emergency stop, defective
emergency stop switch, incorrect or shorted cable, etc.

Error code 16, TIMEOUT HEATING

This error code is generated by the CPU board. The error code is based
on degrees/minutes. A check is made during water filling. If there is a drain
leakage there will be repeated fillings and therefore no error code from gra-
dient check. This timeout is an overall timeout that is started when heating

is started. If heating time is longer than set in HEATING TIMEOUT, SEC

(Config 2) this error code will be activated.

Error code 17, DOOR LOCK

This error code is generated by the CPU board. The error code arises if the
door lock is locked at the start of the wash program, i.e. that the door is
locked although the CPU board has not requested locking.

Error code 18, START NOT ALLOWED

The machine’s program unit has been disabled by a superior monitoring
system.
Actions

• Contact the supplier of the monitoring system for possible causes of the

monitoring system disabling operation of the machine.

Error code 19, MASTER COMM.

Communication with superior system has been broken. The cause can be
an error in the network connections, damaged cable, defective monitoring
system, etc.
Action:

• Contact the supplier of the monitoring system for possible causes of the

monitoring system not communicating.

«
...
118
119
120
121
122
...
»

Summary of Contents for W4300H













































































































































Reviews:

No comments

Related manuals for W4300H

Brand: T-Fal Pages: 38

Family Pro-Fryer

Brand: T-Fal Pages: 18

Brand: T-Fal Pages: 23

Brand: T-Fal Pages: 14

Brand: XPower Pages: 14

Brand: Conair Pages: 2

Dual Basket ProFry

Brand: Presto Pages: 7

BELLEZZA Belle Phon Professional HTD8270

Brand: DCG Pages: 12

Brand: Biodrier Pages: 6

Brand: Maxwell Pages: 16

Brand: Star Pages: 2

Olymp HairMaster

Brand: Belvedere Pages: 28

Brand: Goldair Pages: 5

Brand: Maxwell Pages: 64

Compact Mini Fryer

Brand: Coopers of Stortford Pages: 4

Brand: Samsung Pages: 56

Brand: Samsung Pages: 76

Brand: Samsung Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands