Electrolux W4300H Page 50 Service Manual Download | Manualshive

Page: 50 / 140

background image

50

DISPLAY STATIST. SEC.

Indicate using the knob how long the statistics for COINS – HOUR COUN-
TER – PROGRAM COUNTER are to be displayed when the power to the
machine is switched on. The time is given in steps of 1 second in the range
0 -255 seconds.

SHOW STAT. DOUBLECLI.

Indicate using the knob how long the statistics for COINS – HOUR COUN-
TER– PROGRAM COUNTER are to be displayed following rapidly pressing
the knob twice. The time is given in steps of 1 second in the range 0 -255
seconds.

LAST PROG. TIMEOUT (COIN)

After wash program ended and door opened, the used wash program will
be shown on the display for a certain time. This makes it possible for the
user to see the previous wash program that was selected and used.
When time ended the display will return to show the same as before the
power was cut.

SERVICE INTERVAL HOUR

The machine can show an indication that service is needed on the display.
Select after how many hours the indication shall be shown after last reset
of the service indication.

NOTE!

Only used in CPUs with software for Freescale microprocessor S12

and in GEN6COINOP with software for Hitachi H8 microprocessor.

DRY COM. PORT CPU

and I/O

This is only used on machines with two different control systems such as
Compass and Selecta II.
Select which port on Compass to communicate with the Selecta II timer.

If "Dryer com. Port CPU" is set to YES, the communication to the dryer

timer Selecta II will be done through the RS232 on CPU board. The internal
Communication RS232 port on the CPU for Compass will be used.
If "Dryer com. Port CPU" is set to NO, the communication to the Seleta II
timer can be done through the RS232 port available on I/O-boards. The
address to the I/O-board then needs to be set on the menu line "Dryer
com. Port I/O". If menu line set to zero, no communication accepted by
the Selecta II timer, will be performed on the I/O-board RS232 port.

NOTE!

Both menu lines can not be active at the same time.

The two menu lines are only valid in machines where the software for

the coin program selection interface is used.

Program unit

«
...
48
49
50
51
52
...
»

Summary of Contents for W4300H













































































































































Reviews:

No comments

Related manuals for W4300H

Brand: Blomberg Pages: 44

Brand: DCG Pages: 28

Brand: Omcan Pages: 20

Brand: Linea 2000 Pages: 60

DOMO DELI FRYER XL 4 L

Brand: Linea 2000 Pages: 60

Brand: Alliance Laundry Systems Pages: 87

MSW-IPD-1000-1W

Brand: MSW Motor Technics Pages: 11

Brand: Kenmore Pages: 6

Brand: Kenmore Pages: 2

Brand: Kenmore Pages: 20

8804 - 5.8 cu. Ft. Electric Dryer

Brand: Kenmore Pages: 24

8789 - Elite HE3 7.0 cu. Ft. Electric Dryer

Brand: Kenmore Pages: 56

Brand: Kenmore Pages: 2

Brand: Russell Hobbs Pages: 13

Brand: Kenmore Pages: 1

8751 - 6.7 cu. Ft. HE2 Electric Dryer

Brand: Kenmore Pages: 56

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands