Electrolux W4300H Service Manual Download

Page: 71 / 140

6204

6580

I/O modules

CODE:

10103554

YOUR PASSWORD

0000

ADDRESS I/O BOARD

10.01.00.00

I/O BOARD 1

I/O BOARD 2

I/O BOARD 3

I/O BOARD 4

I/O BOARD 5

Addressing I/O modules

After replacing an I/O module or in instances

where a second module has been added to a
washing machine, the new I/O module must be

addressed in order to activate its function op

tions. The function options of the module are
controlled by the parameter software loaded on

the relevant program device.

• Engage the machine's service mode.
• Highlight the I/O ADDRESS line in the main

menu and press the knob.

The display will now show an 8-digit code.
• Call authorised service and quote the code.
Authorised service will then assign a pass code.
• Enter the code you have been given and

press the knob.

The I/O ADDRESS menu will appear in the dis

play.

• Select wether an I/O module shall be addres

sed or removed.

• If addressed, highlight the I/O module and

press the knob.

• Press the service switch on the I/O module

indicated in the display.

• Where multiple I/O modules are to be addres

sed, repeat the procedure for the relevant

modules.

• Exit the service program.
• If removed, follow the instructions on the

screen and press the service switch on the
I/O module to be removed.

• Where multiple I/O modules to be removed,

repeat the procedure for the relevant modu

les.

• Exit the service program.

MAIN MENU

08.00.00.00

RESET TO FACTORY

ACTIVATE WASH PROGR.

QUICK START BUTTONS

I/O ADDRESS

PRICE PROGRAMMING

EXIT

6204

I/O ADDRESS

10.01.00.00

ADDRESS I/O BOARD

REMOVE I/O BOARD

EXIT

Summary of Contents for W4300H













































































































































Search results

Summary of Contents for W4300H

Reviews:

Related manuals for W4300H

Brands by name

Popular brands

Electrolux W4300H, Service Manual

Search results

Summary of Contents for W4300H

Reviews:

Related manuals for W4300H

Brands by name

Popular brands