Electrolux W4300H Service Manual Download

Page: 102 / 140

102

Payment systems

Abbreviation

Explanation

EBSK

Electrolux BokningsSystem Kommunicerande.

Supplied with interface for central booking/payment system EBSK.

PCPXS

Prepared Central Payment eXternal Start.

Prepared for central payment system with external start, e.g. for the

French market.

PCB

Prepared Central Booking.

Prepared for central booking/payment system, i.e., Coges, Camping.

EBS

Electrolux Booking System.

Prepared for central booking/payment system EBS, also for i.e. Aptus,

In-time.

PXS

Prepared eXternal Start.

Prepared for external start/pause, e.g. for gas-heated machines.

DELAY

Supplied with timer for delayed start, e.g. on machines with wash programs

for Farm/Cow-Cloths.

Summary of Contents for W4300H













































































































































Search results

Summary of Contents for W4300H

Reviews:

Related manuals for W4300H

Brands by name

Popular brands

Electrolux W4300H, Service Manual

Search results

Summary of Contents for W4300H

Reviews:

Related manuals for W4300H

Brands by name

Popular brands