Electrolux W4300H Service Manual Download

Page: 101 / 140

101

Payment systems

Various systems for payment and booking systems are available.

See below table.

Abbreviation

Explanation

CMS

Coin Meter Single.

Supplied with coin meter, single slot.

CMD

Coin Meter Double.

Supplied with coin meter, double slot.

CMSL

Coin Meter Single Latch.

Supplied with coin meter, single slot. With latch for coin interlock.

CMB

Coin Meter with strong box housing, no coin box.

CMDSL

Coin Meter Double Single Latch.

Supplied with coin meter double coin, single slot.

With latch for coin interlock.

CME

Coin Meter Electronic.

Supplied with electronic coin meter.

PCM

Prepared Coin Meter.

Prepared for coin meter.

PCMB

Prepared Coin Meter Box.

As PCM but with strong box housing, no coin box.

PCMSB

Prepared Coin Meter Supply voltage Box.

As PCM but with power supply and strong box housing, no coin box.

ESS

Electrolux Single System.

Supplied with Electrolux Single System for AHL.

PCMX

Prepared Coin Meter eXternal.

Supplied with interface for external coin meter.

CPC

Central Payment Coin.

Supplied with interface for central payment system.

E.g. EFS (Electrolux Flex System). CP/Calcad 80/800/900/1000/2000.

EMS

Electrolux Master System.

Supplied with interface for central control EMS.

LM10

Laundry Management. Communicates via the ELS Network

ELS-bokn

Electrolux Laundry System and booking system. Communicates via the ELS

Network.

Payment systems

Summary of Contents for W4300H













































































































































Search results

Summary of Contents for W4300H

Reviews:

Related manuals for W4300H

Brands by name

Popular brands

Electrolux W4300H, Service Manual

Search results

Summary of Contents for W4300H

Reviews:

Related manuals for W4300H

Brands by name

Popular brands