Eiki LC-XT6, Service Manual

Page: 95 / 286

-95-
Electrical Adjustment
Grp / No. Item Function Range Initial Note
200 Option
0 Logo Display Prohibition 0:Menu 1:Forced 0 - 1 0
1 RS232C Baud rate 0: 19200bps 1: 9600bps 0 - 1 0
4 CABLE SW Long Cable 0: Disable 1: Enable 0 - 1 0
6 Device Refresh Disable 0: Enable 1: Disable 0 - 1 0
8 PJ-NET HUNGUP CHK 0: Disable 1: Enable 0 - 1 0
51 Filter Warning Display 1:On 0:Off 0 - 1 1
53 Filter Counter Reset Times Read only 0 - 255 0
54 Factory Default Executed Times Read only 0 - 255 0
56 Menu Position (X) X Offset 0 - 1024 0
57 Menu Position (Y) Y Offset 0 - 1024 0
72 COMPONENT/RGB SW 0: Disable 1: Enable 0 - 1 1
140 OFFSET ADD MODE
Offset Tem Add Mode Display
0: No Addition, 1: Addtion
- 0
141 OFFSET ADD CHNG Apply Offset Change when the data is set 10 0 - 10 0
142 OFFSET Offset Temp - 10
143 TIMES OF OFFSET CHANGE 0 - 255 0
144 TIMES OF OFFSET RESET 0 - 255 0
201 Option (Signal) Not Used
0 FrameLock Option
Frame Lock Setting
0: OFF for PC
1: OFF for AV
2: OFF
3: ON Depending on Input Frequency
4: ON Depending on Input Frequency
0 - 4 4
204 Simulation mode
0 Scaler Enable 0: Off, 1: On 0 - 1 0
205 Spread Spectrum
0 Enable 0: Off, 1: On 0 - 1 1
1 Spread Rate Default 41 0 - 82 41
2 Spread Frequency Default 0 0 - 2 0
220 Projector Error Log
0 Warning_Log_1 Latest Error log 0 - 32767 0
: : : : :
49 Warning_Log_50 50th Error log 0 - 32767 0
50 Warning_Log Reset Log is cleared when the value is set to 10. 0 ~ 10 0
235 Shutter
0 Power ON_OFF Motion Shutter Warm - up Operation (0: Yes, 1: No) 0 - 1 Initial: 1 / Shipping: 0
1 CMP_TRM Chattering Detecting Term 0 - 32767 7000
2 OUT_DLY_TRM Output Term 0 - 32767 15000
3 CMP_CHK_CNT Count of Information Sync 0 - 15 5
4 OPEN_DLY Open Output Delay 0 - 63 0
5 CLOSE_DLY Close Output Delay 0 - 63 0
6 Position Check Time Position Check Time 1 - 255 30
7 Stop Mode
Shutter Operation in Stop Mode
0:Free, 1:Brake
0 - 1 0
8 Enable Close Cmd
Shutter Close Command
0:Disable, 1:Enable
0 - 1 1
10 Shutter Management Upper Time 180 - 999 480
240 Flow Calibration
0 Flow Calibration Exe
Flow Sensor Offset Calibration Start calibration when the value is
set to 1.
0 - 1 0
1 Flow Calibration Error Log
Log of Calibration Error (Read only)
255: Not Calibration
0: No Error
10: 1st Calibration Not Stable Airflow
11: 1st Calibration Out of Range
20: 2nd Not Stable Airflow
21: 2nd Out of Range
100: 10th Calibration Not Stable Airflow
101: 10th Calibration Out of Range
- 255
2 Clog Check Enable Filter Clogged Detection by Flow Sensor (0: Disable, 1: Enable) 0 - 1 Initial: 0 / Shipping: 1
3 Air Inlet Check Enable Intake Vent Error Check (0: Disable, 1: Enable) 0 - 1 Initial: 0 / Shipping: 1
5 Clog Auto Cooling Enable Cooling on Clog (0: Disable, 1: Enable) 0 - 1 1
6 Scroll Fail Auto Cooling Enable Cooling on Scroll error (0: Disable, 1: Enable) 0 - 1 1
8 Filter Counter Remaining Enable Filter Counter Remaining Function (0: Disable, 1: Enable) 0 - 1 1
13 Filter Stanbdard Limit Filter life (x100 hour) 0 - 255
Normal filter: 50
Special filter: 10
14 Filter Max Limit Filter Limit (x100 hour) 0 - 255
Normal filter: 60
Special filter: 15