Edwards D397-50-000 Instruction Manual Download Page 4

Page: 4 / 76

D397-50-880 Issue C

Page ii

Edwards and the Edwards logo are trademarks of Edwards Limited.

Contents

4.8.4

Software module 860 - DX Pump Power .............................................................................29

4.8.5

Software module 869 - DX Pump Speed Set-up ....................................................................29

4.8.6

Software module 875 - DX Vent Valve close ........................................................................29

4.8.7

Software module 902 - TIC Software Version .......................................................................30

4.8.8

Software module 904 - Turbo Pump control ........................................................................30

4.8.9

Software module 905 - Turbo Pump Speed .........................................................................31

4.8.10

Software module 906 - Turbo Pump Power .........................................................................32

4.8.11

Software module 907 - Turbo Normal ...............................................................................32

4.8.12

Software module 908 - Turbo Standby ..............................................................................32

4.8.13

Software module 909 - Turbo Cycle Time ...........................................................................33

4.8.14

Software module 910 - Backing pump control ......................................................................33

4.8.15

Software module 911 - Backing pump speed .......................................................................34

4.8.16

Software module 912 - Backing pump power .......................................................................34

4.8.17

Linking gauges and pumps .............................................................................................34

4.8.18

Software module 913 - Gauge 1 ......................................................................................35

4.8.19

Software module 914 - Gauge 2 ......................................................................................36

4.8.20

Software module 915 - Gauge 3 ......................................................................................36

4.8.21

Linking Relay set point outputs .......................................................................................36

4.8.22

Software module 916 - Relay 1 .......................................................................................37

4.8.23

Software module 917 - Relay 2 .......................................................................................37

4.8.24

Software module 918 - Relay 3 .......................................................................................38

4.8.25

Software module 919 - TIC Power supply temperature ...........................................................38

4.8.26

Software module 920 - TIC internal temperature .................................................................38

4.8.27

Software module 921 - Analogue output ............................................................................39

4.8.28

Software module 922 - TIC Vent valve ..............................................................................39

4.8.29

Software module 923 - Heater band .................................................................................40

4.8.30

Software module 924 - Air Cooler (Fan) .............................................................................40

4.9

Response time calculations & Measurements ......................................................................41

Maintenance ..................................................................................... 43

5.1

Fault finding .............................................................................................................43

5.2

Factory defaults .........................................................................................................44

5.3

Software upgrades ......................................................................................................48

5.4

Fuse replacement (DX version only) .................................................................................50

Storage and Disposal ........................................................................... 51

6.1

Storage ...................................................................................................................51

6.2

Disposal ................................................................................................................... 51

Spares and Accessories ........................................................................ 53

7.1

Introduction .............................................................................................................53

7.2

Spares ..................................................................................................................... 53

7.3

Accessories ...............................................................................................................53

Appendix A1 Full Pump States ......................................................................... 55

Appendix A2 Alert ID .................................................................................... 56

Appendix A3 Priority .................................................................................... 57

Appendix A4 Command List ............................................................................ 58

Appendix A5 Active Gauge States ..................................................................... 59

Index .............................................................................................. 61

For return of equipment, complete the HS Forms at the end of this manual.

Summary of Contents for D397-50-000








































































Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands

Edwards D397-50-000, Instruction Manual

Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands