Edwards D397-50-000 Instruction Manual Download Page 44 | Manualshive

Page: 44 / 76

background image

D397-50-880 Issue C

Page 38

© Edwards Limited 2010. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

4.8.29

Software module 923 - Heater band

General Description

Control, set-up and monitoring of the Heater band control output.

Output bytes (from Master)

Note:

Manual control is only available when the turbo pump has reached ’normal speed’ and either the heater
band on time is set to ’0’ or the heater time has not expired.

Input bytes (to Master)

No Alerts currently exist for this software module so the 4th and 5th bytes will always be zero.

Associated Parameter options

4.8.30

Software module 924 - Air Cooler (Fan)

General Description

Set-up and monitoring of the TIC Air cooler (fan).

Output bytes (from Master)

None - No direct user control.

Input bytes (to Master)

No Alerts currently exist for this software module so the 2nd and 3rd bytes will always be zero.

Associated Parameter options

1st

Manual control (0=Off, 1=On, 99=leave alone)

1st

First two bytes form a 16-bit number which is the time in
minutes that the heater band has remaining.

2nd

3rd

State - 0 = on, 4 = off.

4th

Alert - refer to table in Appendix A2.

5th

Priority - refer to table in Appendix A3.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Heater band on time

The number of hours that the heater band will be on for once
started. The turbo pump reaching normal speed initiates
heater band operation. If the turbo speed drops below normal
the heater band will switch off and the timer will be reset. If
this facility is to be used the output byte value should be 99.

1st

State - 0 = off, 4 = on.

2nd

Alert - refer to table in Appendix A2.

3rd

Priority - refer to table in Appendix A3.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Function

Determines the operation of the air cooler output. Options are
either: Always On=0. On with the turbo=1.

«
...
42
43
44
45
46
...
»

Summary of Contents for D397-50-000













































































Reviews:

No comments

Related manuals for D397-50-000

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: GCE Pages: 24

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: IBA Pages: 29

Brand: Contemporary Research Pages: 22

Brand: FOR-A Pages: 6

Brand: turck Pages: 45

Brand: Thermo Scientific Pages: 68

Brand: Pacostar Pages: 55

ZigBee ZSCAN16 MIRROR

Brand: NCD Pages: 12

Brand: OCL Pages: 2

Rite-Temp K-8304-K

Brand: Kohler Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands