Edwards D397-50-000 Instruction Manual Download Page 8 | Manualshive

Page: 8 / 76

background image

D397-50-880 Issue C

Page 2

© Edwards Limited 2010. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Introduction

1.2

Product description

There are two variants of the Profibus Module, both of which are provided with a standard Profibus connection, DC
power input connection and connection to the Edwards equipment. The TIC Profibus Module is provided with a short
serial cable to connect the module to the TIC serial comms port. The DX Profibus Module is provided with a 15 way
connector. The 15 way flying lead attached to the DX pump can be directly connected for both power and control.

This manual explains how to control and monitor the TIC and DX Pump modules with a Profibus system. Please refer
to the following manuals for operation of TIC controllers and DX pumps:

D397-12-880

Turbo Controller

D397-21-880

Instrument Controller

D397-22-880

Turbo Instrument controller

D397-30-880

TIC serial comms manual

B722-40-880

DX Pumps

WARNING

Improper use of the equipment may impair the protection provided and could cause damage to it.

WARNING

The equipment is used to remotely control other equipment that could be hazardous if used
inappropriately. The responsibility for the safe operation and maintenance of the equipment
being controlled is with the user.

WARNING

The data received from this unit should not be used for safety purposes.

«
...
6
7
8
9
10
...
»

Summary of Contents for D397-50-000













































































Reviews:

No comments

Related manuals for D397-50-000

Brand: Falcon Pages: 3

Brand: Eaton Pages: 16

Brand: Manfrotto Pages: 16

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: Harmonic Drive Pages: 25

Brand: Nelson Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 12

Brand: FAAC Pages: 44

Brand: FAAC Pages: 44

Brand: FAAC Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 14

Brand: FAAC Pages: 68

Brand: FAAC Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands